“This site contains affiliate links for which OEMDTC may be compensated” |
April 23, 2019 NHTSA CAMPAIGN NUMBER: 19V318000
Door Spot Welds Affecting Air Bag Deployment
The incorrect air bag sensor readings could cause the affected air bags to unintentionally deploy or to not deploy when intended, increasing the risk of a crash and/or injury.
NHTSA Campaign Number: 19V318
Manufacturer Toyota Motor Engineering & Manufacturing
Components AIR BAGS
Potential Number of Units Affected 274
Summary
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2019 Sienna vehicles. The passenger front door may have incorrect welds inside, possibly affecting the air bag sensor readings for the passenger side front seat and curtain shield air bags.
Remedy
Toyota will notify owners, and dealers will replace the passenger side front door sub assembly with a new one, free of charge. The recall began June 21, 2019. Owners may contact Toyota customer service at 1-888-270-9371. Toyota’s number for this recall is K1G /K0G.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Check if your Vehicle has a Recall
Original Publication Date: June 13, 2019
To: All Toyota Dealer Principals, General Managers, Service Managers, and Parts Managers
SAFETY RECALL K0G (Remedy Notice)
Certain 2019 Model Year Sienna Vehicles
Potential Unintended or Non-Deployment of Passenger Side Front Seat and Curtain Shield Airbags
NHTSA Recall No. 19V-318
Model / Years | Production Period | Approximate Total Vehicles | Approximate Stop Sale Dealer Inventory |
---|---|---|---|
2019 Sienna | Mid-February 2019 | 270 | 67 |
STOP! DO NOT SELL NEW VEHICLES IN DEALER INVENTORY.Refer to Dealer Inventory Procedures section for more details. |
On April 23,2019, Toyota filed a Defect Information Report (DIR) with the National Highway Traffic Safety Administration (NHTSA) informing the agency of our intent to conduct a voluntary Safety Recall on certain 2019 Model Year Sienna vehicles.
Condition
During the manufacturing process of the passenger side front doors, it is possible that a component may not have been welded properly. This could affect an airbag system sensor and lead to nondeployment or inadvertent deployment of the passenger side front seat and curtain shield airbags. This can increase the risk of a crash or injury in the event of a crash.
Remedy
Any authorized Toyota dealer will replace the passenger side front door sub-assembly with a new one FREE OF CHARGE.
NOTE: The remedy involves the replacement of the passenger side front door sub-assembly. All other door components such as the interior door panel, window, moldings, door handle, etc. will be reused. The door will also require painting. Installation of the new door sub-assembly, re-installation of the other door components, and painting will be covered by this recall remedy.
Covered Vehicles
There are approximately 270 vehicles covered by this Safety Recall. No vehicles, involved in this Safety Recall, were distributed to Puerto Rico.
Owner Letter Mailing Date
Toyota will notify owners by mid – June 2019. A sample of the owner notification letter has been included for your reference.
Toyota makes significant effort to obtain current customer name and address information from each state through industry resources when mailing owner letters. In the event your dealership receives a notice for a vehicle that was sold prior to the Safety Recall announcement, it is the dealership’s responsibility to forward the owner letter to the customer who purchased the vehicle.
Please note that only owners of the covered vehicles will be notified. If you are contacted by an owner who has not yet received a notification, please verify eligibility by confirming through TIS prior to performing repairs. Dealers should perform the repair as outlined in the Technical Instructions found on TIS.
Dealer Inventory Procedures
New Vehicles in Dealership Inventory
There are approximately 67 vehicles in new dealer inventory as of April 22,2019.
Under Title 49, Section 30112 of the United States Code, a dealer cannot sell, offer for sale, or introduce or deliver for introduction in interstate commerce a new motor vehicle when it is aware that the vehicle does not comply with an applicable Federal Motor Vehicle Safety Standard or contains a defect related to motor vehicle safety. Further, 49 Code of Federal Regulations §577.13 requires us to provide the following advisory: It is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by this notification under a sale or lease until the defect or noncompliance is remedied.
Toyota reimburses dealers for flooring costs associated with new vehicles held in dealership inventory until the recall remedy becomes available. Toyota provides these flooring reimbursements at 60 day intervals. Toyota reserves the right to withhold or charge-back any flooring reimbursement funds that may have been paid to the dealer if it determines that a new vehicle subject to a safety recall was sold without first being remedied. |
|
Vehicle Safety Recall completion should always be verified through TIS. We request your assistance to ensure involved vehicles are identified and not delivered prior to performing the remedy. |
NOTE: Dealers can identify if any of their new and used inventory has any open campaigns in the Vehicle Inventory Summary available in Dealer Daily (https://dealerdaily.toyota.com/). The Vehicle Inventory Summary may take up to 4 hours to populate information for newly launched campaigns.
New Vehicles in Dealership Inventory – Post Repair Handling
All vehicles in new dealer inventory should be inspected and repaired as outlined in the Technical Instructions. Due to the extent of the repair necessary to replace the passenger side front door sub-assembly, Toyota will repurchase these vehicles from the dealer and replace that inventory with another similar vehicle. For vehicles that require passenger side front door sub-assembly replacement, follow the instructions outlined below:
- Complete passenger side front door sub-assembly replacement and file the campaign claim;
- Contact the regional vehicle supply manager after the campaign is completed.
The region will administer the vehicle repurchase and replace that inventory with another similar vehicle.
Inspection Reminder Mirror Hang Tags for Covered Vehicles in New Dealer Stock
To easily recognize vehicles involved in this Safety Recall, each dealership should utilize Inspection Reminder Hang Tags. Inside the vehicle’s glove box are stickers containing the VIN. Apply one of these stickers to the hang tag and install the hang tag in the vehicle. A sample copy of the Inspection Reminder Hang Tag has been included for your reference.
Part Number | Description | Quantity |
---|---|---|
00411-140003 | Inspection Mirror Hang Tag | 25 Per Pack |
NOTE: Dealerships can order hang tags from the Material Distribution Center (MDC).
Pre-Owned Vehicles in Dealer Inventory
To ensure customer satisfaction, Toyota requests that dealers complete this Safety Recall on any used vehicles currently in dealer inventory that are covered by this Safety Recall prior to customer delivery. However, if the campaign cannot be completed (for example, due to remedy parts availability), delivery of a covered vehicle is acceptable if disclosed to the customer that the vehicle is involved in a Safety Recall.
Toyota expects dealers to use the attached Customer Contact and Vehicle Disclosure Form to obtain vehicle buyer information. Dealers are expected to provide a copy of the completed form, along with the most current FAQ, to the vehicle buyer. Toyota and the dealer may use this information to contact the customer when the remedy becomes available.
Keep the completed form on file at the dealership and send a copy to quality_compliance@toyota.com. In the subject line of the email state “Disclosure Form K0G/K1G” and include the VIN.
NOTE: Dealers can identify if any of their new and used inventory has any open campaigns in the Vehicle Inventory Summary available in Dealer Daily (https://dealerdaily.toyota.com/). The Vehicle Inventory Summary may take up to 4 hours to populate information for newly launched campaigns.
Toyota Certified Used Vehicle (TCUV)
The TCUV policy prohibits the certification of any vehicle with an outstanding Safety Recall, Special Service Campaign, or Limited Service Campaign. Thus, no affected units are to be designated, sold, or delivered as a TCUV until all applicable Safety Recalls, Special Service Campaigns, and Limited Service Campaigns have been completed on that vehicle.
Toyota Rent-A-Car (TRAC) & Service Loaners
Toyota requests that dealers remove all TRAC and Service Loaner vehicles from service that are covered by a Safety Recall unless the defect has been remedied.
Customer Handling, Parts Ordering, and Remedy Procedures
Customer Contacts
Customers who receive the owner letter may contact your dealership with questions regarding the letter and/or the Safety Recall. Please welcome them to your dealership and answer any questions that they may have. A Q&A is provided to assure a consistent message is communicated.
Customers with additional questions or concerns are asked to please contact the Toyota Customer Experience Center (1-888-270-9371) – Monday through Friday, 7:00 am to 7:00 pm, Saturday 7:00 am to 4:30 pm Central Time.
Media Contacts
It is imperative that all media contacts (local and national) receive a consistent message. In this regard, all media contacts must be directed to Tania Saldana (859) 815-9968 in Toyota Corporate Communications. Please do not provide this number to customers. Please provide this contact only to media.
Parts Ordering Process – Non SET and GST Parts Ordering Process
It is possible that parts for this campaign are either required to be ordered in Campaign Part Order Request (CPOR) on Service Lane, or have been placed on Manual Allocation Control (MAC) due to potential limited part availability. Please check the CPOR/MAC report on Dealer Daily for the most up-to-date parts ordering information.
All Safety Recall, Service Campaign (SSC/LSC) parts are eligible for the Monthly Parts Return Program. Please refer to PANT Bulletin 2011-087 for campaign parts that are currently returnable under the Monthly Parts Return Program and for additional details.
Description | Quantity | Part Number |
---|---|---|
PANEL SUB-ASSY, FRONT DOOR, RH | 1 | 67001-08070 |
BUTYL TAPE | 1 | 04003-49233 |
FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY | 1 | 68160-08020 |
FRONT DOOR SERVICE HOLE COVER | 1 | 67831-08020 |
TAPE, BLACK OUT FRONT DOOR, INNER REAR RH | 1 | 75968-08010 |
TAPE, BLACK OUT FRONT DOOR, OUTER REAR RH | 1 | 75957-08010 |
TAPE, BLACK OUT FRONT DOOR, OUTER UPPER RH | 1 | 75955-08010 |
TAPE, BLACK OUT FRONT DOOR, INNER UPPER RH | 1 | 75929-08010 |
GROMMET, SCREW (Inside Handle) | 1 | 90189-05003 |
GROMMET, SCREW (Arm rest) | 1 | 90901-89021 |
GROMMET, SCREW (Door Panel) | 1 | 90189-04200 |
GROMMET, SCREW (Speaker) | 4 | 90189-06227 |
DOOR FRAME GARNISH | 1 | 67663-08010 |
DOOR LOCK WIRE HARNESS SEAL | 1 | 69318-AA010 |
CLAMP, WIRING HARNESS | 1 | 82711-1E360 |
Parts that MAY be needed for some vehicles:
Non-shoulder, hinge bolts for adjustment | 4 | 90084-10049 |
Door Moulding (Bright Chrome) | 1 (Optional Accessory) | PT29A-08100 |
Technician Training Requirements
The repair quality of covered vehicles is extremely important to Toyota. All dealership technicians performing this repair are required to successfully complete the most current version of the E-Learning course “Safety Recall and Service Campaign Essentials”. To ensure that all vehicles have the repair performed correctly; technicians performing this repair are required to currently hold at least one of the following certification levels:
- Certified Technician (Any Specialty)
- Expert Technician (Any Specialty)
- Master Technician
- Master Diagnostic Technician
Always check which technicians can perform the repair by logging on to https://www.uotdealerreports.com. It is the dealership’s responsibility to select technicians with the above certification level or greater to perform this repair. Carefully review your resources, the technician skill level, and ability before assigning technicians to this repair. It is important to consider technician days off and vacation schedules to ensure there are properly trained technicians available to perform this repair at all times.
Remedy Procedures
Refer to TIS for Technical Instructions on repair. Conduct all non-completed Safety Recalls and Service Campaigns on the vehicle during the time of appointment.
Repair Quality Confirmation
The repair quality of covered vehicles is extremely important to Toyota. To help ensure that all vehicles have the repair performed correctly, please designate at least one associate (someone other than the individual who performed the repair) to verify the repair quality of every vehicle prior to customer delivery.
Parts Recovery Procedures
All parts replaced as part of this Safety Recall must be turned over to the parts department until appropriate disposition is determined. The parts department must retain these parts until notification via the Parts Recovery System (PRS) is received indicating whether to ship or scrap the parts. These parts are utilized by various departments for defect analysis, quality control analysis, product evaluation, as well as other purposes.
To help minimize dealer storage challenges, Toyota recommends that dealers:
- File the campaign claim accurately and promptly. The time a dealer is required to hold parts is based on when the campaign claim is paid by Toyota.
- Monitor the Warranty Parts Recovery Notifications and Part Scrap Report regularly.
Refer to Warranty Policies 9.3 and 9.6 for additional details.
Warranty Reimbursement Procedures
Loaner Vehicle Reimbursement Procedure
If the customer requested a rental during the Interim period, a loaner vehicle or alternative transportation through Toyota Rent-A-CAR (TRAC) can be claimed for $35 per day.
Op Code | Description |
UGG26A | Vehicle Rental 1-30 Days |
UGG26B | Vehicle Rental 31-50 Days |
NOTE:
- Rental invoice MUST be attached to all rental claims. These claims may be subject to debit if rental invoice is not attached.
- Rentals that exceed the maximum allowable daily rate will require DSPM authorization per the Toyota Transportation Assistance Policy (TTAP).
Warranty Reimbursement Procedure
Op Code | Description | Flat Rate Hours |
K0G001 | Replace the passenger side door + Paint the passenger side door (By Dealership) | 9.3 hrs/vehicle |
K0G002 | Replace the passenger side door + Paint the passenger side door (By External Body Shop) | 2.0 hrs/vehicle |
NOTE: The 2.0 flat rate hours under Op Code K0G002 is for the disassembly and reassembly of the door at the dealership. All refinishing costs are to be claimed as a sublet as described below.
- The flat rate times include 0.2 hours for administrative cost per unit for the dealership.
- The cost for the paint materials can be claimed under Op Code K0G001 as sublet type “PT”.
- The cost for the paint, materials, and door refinishing can be claimed under Op Code K0G002 as sublet type “PT”.
- A loaner vehicle or alternative transportation through the Toyota Rent-A-Car (TRAC) can be claimed up to a maximum of 2 days as a sublet type “RT” under Op Codes K0G001 or K0G002.
- For rentals that exceed the maximum number of allowable days and/or dollars per day, refer to the Toyota Transportation Assistance Policy (TTAP) for DSPM authorization requirements.
- Rental invoice MUST be attached to all rental claims. These claims may be subject to debit if rental invoice is not attached.
Claim Filing Accuracy and Correction Requests
It is the dealer’s responsibility to file claims correctly for this Safety Recall. This claim filing information is used by Toyota for various government reporting activities; therefore, claim filing accuracy is crucial. If it has been identified that a claim has been filed using an incorrect Op Code or a claim has been filed for an incorrect VIN, refer to Warranty Procedure Bulletin PRO17-03 to correct the claim.
Campaign Designation / Phase Decoder
Please review this entire package with your Service and Parts staff to familiarize them with the proper step-by step procedures required to implement this Safety Recall.
Thank you for your cooperation.
TOYOTA MOTOR SALES, U.S.A., INC.
SAFETY RECALL K0G (Remedy Notice)
Certain 2019 Model Year Sienna Vehicles
Potential Unintended or Non-Deployment of Passenger Side Front Seat and Curtain Shield Airbags
NHTSA Recall No. 19V-318
Frequently Asked Questions
Original Publication Date: June 13, 2019
Q1: | What is the condition? | ||||||
A1: | During the manufacturing process of the passenger side front doors, it is possible that a component may not have been welded properly. This could affect an airbag system sensor and lead to nondeployment or inadvertent deployment of the passenger side front seat and curtain shield airbags. This can increase the risk of a crash or injury in the event of a crash.
|
||||||
Q2: | Are there any warnings that this condition exists? | ||||||
A2: | No. There are no warnings that this condition exists.
|
||||||
Q3: | What is Toyota going to do? | ||||||
A3: | Toyota is currently preparing the remedy. When the remedy becomes available, any authorized Toyota dealer will replace the passenger side front door sub-assembly FREE OF CHARGE.
Q3a: What is a “door sub-assembly”? A3a: The door sub-assembly is the door without any trim or components added to it. All other door components such as the interior door panel, window, moldings, door handle, etc. will be reused. The door sub-assembly will also require painting. Installation of the new door subassembly, re-installation of the other door components, and painting will be covered by this recall remedy.
|
||||||
Q4: | Which and how many vehicles are covered by this Safety Recall? | ||||||
A4: | There are approximately 270 vehicles covered by this Safety Recall.
Q4a: Are there any other Lexus/Toyota/Scion vehicles covered by this Safety Recall in the U.S.? A4a: No, there are no other Lexus/Toyota/Scion vehicles covered by this Safety Recall.
|
||||||
Q5: | How long will the repair take? | ||||||
A5: | The repair takes approximately nine hours. However, depending upon the dealer’s work schedule, it may be necessary to make the vehicle available for a longer period of time.
|
||||||
Q6: | How does Toyota obtain my mailing information? | ||||||
A6: | Toyota uses an industry provider who works with each state’s Department of Motor Vehicles (DMV) to receive registration or title information, based upon the DMV records. Please make sure your registration or title information is correct.
|
||||||
Q7: | What if I have additional questions or concerns? | ||||||
A7: | If you have additional questions or concerns, please contact the Toyota Customer Experience Center at 1-888-270-9371 Monday through Friday, 7:00 am to 7:00 pm, Saturday 7:00 am to 4:30 pm Central Time.
|
SEOCONTENT-START
TECHNICAL INSTRUCTIONS
FOR
SAFETY RECALL K0G
POTENTIAL UNINTENDED OR NON-DEPLOYMENT OF PASSENGER SIDE FRONT SEAT AND CURTAIN SHIELD AIRBAGS
CERTAIN 2019 SIENNA
The repair quality of covered vehicles is extremely important to Toyota. All dealership technicians performing this recall are required to successfully complete the most current version of the E-Learning course “Safety Recall and Service Campaign Essentials”. To ensure that all vehicles have the repair performed correctly; technicians performing this recall repair are required to currently hold at least one of the following certification levels:
• Certified Technician (any specialty)
• Expert Technician (any specialty)
• Master Technician
• Master Diagnostic Technician
It is the dealership’s responsibility to select technicians with the above certification level or greater to perform this recall repair. Carefully review your resources, the technician skill level, and ability before assigning technicians to this repair. It is important to consider technician days off and vacation schedules to ensure there are properly trained technicians available to perform this repair at all times.
2
I. OPERATION FLOW CHART
Covered
Campaign completed, return
the vehicle to the customer
Verify Vehicle Eligibility
1. Confirm vehicle VIN matches the RO.
2. Check Vehicle Inquiry System for
eligibility.
..Not Covered.. No further action required
Paint the NEW passenger front door
Complete any necessary Initilizations
Destroy the original passenger
front door
Install and reassemble the NEW
passenger front door
Disassemble and remove the original
passenger front door
3
II. IDENTIFICATION OF AFFECTED VEHICLES
1. CHECK VEHICLE FOR CAMPAIGN ELIGIBILITY
a. Compare the vehicles VIN to the VIN listed on the Repair Order to ensure they match.
b. Check the TIS Vehicle Inquiry System to confirm the VIN is involved in this Campaign, and
that it has not already been completed.
Note: TMNA warranty will not reimburse dealers for repairs completed on vehicles that are not
affected or were previously completed, even by another dealer.
III. PREPARATION
A. PARTS
Parts required for each vehicle:
Part Number Part Description Quantity
67001-08070 PANEL SUB-ASSY, FRONT DOOR, RH 1
04003-49233 BUTYL TAPE 1
68160-08020 FRONT DOOR GLASS OUTER WEATHERSTRIP
ASSEMBLY
1
67831-08020 FRONT DOOR SERVICE HOLE COVER 1
75968-08010 TAPE, BLACK OUT FRONT DOOR, INNER REAR RH 1
75957-08010 TAPE, BLACK OUT FRONT DOOR, OUTER REAR RH 1
75955-08010 TAPE, BLACK OUT FRONT DOOR, OUTER UPPER RH 1
75929-08010 TAPE, BLACK OUT FRONT DOOR, INNER UPPER RH 1
90189-05003 GROMMET, SCREW (Inside Handle) 1
90901-89021 GROMMET, SCREW (Arm rest) 1
90189-04200 GROMMET, SCREW (Door Panel) 1
90189-06227 GROMMET, SCREW (Speaker) 4
67663-08010 DOOR FRAME GARNISH 1
69318-AA010 DOOR LOCK WIRE HARNESS SEAL 1
82711-1E360 CLAMP, WIRING HARNESS 1
Parts that may be needed for some vehicles:
Part Number Part Description Quantity
90084-10049 Non-shoulder, hinge bolts for adjustment 4
PT29A-08100 Door Moulding (Bright Chrome) – trim level 1
IV. BACKGROUND
During the manufacturing process of the passenger side front doors, it is possible that a
component may not have been welded properly. This could affect an airbag system sensor and
lead to nondeployment or inadvertent deployment of the passenger side front seat and curtain
shield airbags. This can increase the risk of a crash or injury in the event of a crash.
4
V. COMPONENTS
5
6
7
8
VI. DISASSEMBLY AND REMOVAL
1. DISASSEMBLE THE ORIGINAL PASSENGER FRONT DOOR
a. Follow the Repair Manual instructions to remove the components from the original passenger
side front door. These parts will be reused, so be careful during disassembly.
DOOR / HATCH: FRONT DOOR: DISASSEMBLY; 2018 – 2020 MY Sienna
(RM1000000018DTB)
b. Remove the door handle nut from the original door, as it will be reused. The nut will slide
forward to be removed.
c. Pull the wire harness through the door. It is not necessary to pull the harness through the Apillar.
2. REMOVE ORIGINAL DOOR
a. Unbolt the door from the hinges.
3. DESTROY THE ORIGINAL DOOR
a. Using a large hammer, damage the hinge area of the original door to ensure that this door
cannot be reused again.
VII. INSTALLATION AND ADJUSTMENT
1. PAINT NEW DOOR
a. Properly paint the NEW door.
2. INSTALL NEW DOOR
a. Install the NEW door onto the vehicle.
b. Properly adjust the NEW door using the procedure detailed in the Repair Manual.
DOOR / HATCH: FRONT DOOR: ADJUSTMENT; 2016 – 2020 MY Sienna
(RM100000000VK8E)
9
VIII. REASSEMBLY
1. REASSEMBLE THE NEW PASSENGER SIDE FRONT DOOR
a. Install the NEW plastic clips as detailed in the diagram below.
b. Push the wire harness into the NEW door.
c. Install the door handle nut into the NEW door, as removed in step VI. 1b on page 8.
d. Follow the Repair Manual procedure to reassemble the NEW door.
DOOR / HATCH: FRONT DOOR: REASSEMBLY; 2018 – 2020 MY Sienna
(RM1000000018DTF)
e. If originally equipped, install a NEW door moulding.
IX. INITIALIZATIONS
1. COMPLETE NECESSARY INITIALIZATIONS
a. Follow the Repair Manual complete any necessary initializations.
INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION; 2018 – 2020 MY Sienna
(RM1000000018R4B)
10
◄ VERIFY REPAIR QUALITY ►
• Confirm the new door is properly adjusted.
• Confirm the window and door locks work properly.
• Confirm the original door has been properly destroyed.
If you have any questions regarding this update, please contact your regional representative.
X. APPENDIX
A. PARTS DISPOSAL
As required by Federal Regulations, please make sure all recalled parts (original parts)
removed from the vehicle are disposed of in a manner in which they will not be reused,
unless requested for parts recovery return.
B. CAMPAIGN DESIGNATION DECORDER
H 0 A
Year Campaign is Launched
B = 2011
C = 2012
D = 2013
E = 2014
F = 2015
G = 2016
H = 2017
Etc…
Repair Phase
1st Campaign = A
2nd Campaign = B
3rd Campaign = C
4th Campaign = D
5th Campaign = E
27th Campaign = 1
28th Campaign = 2
Etc…
Current Campaign Letter
for this year
0 = Remedy
1 = Interim (Remedy not yet
available) will change to
when the Remedy is available
(May use other characters in
unique cases)
Examples:
C1B = Launched in 2012, Interim Phase, 2nd Campaign Launched in 2012
E0A = Launched in 2014, Remedy Phase, 1st Campaign Launched in 2014
H0A = Launched in 2017, Remedy Phase, 1st Campaign Launched in 2017.
SEOCONTENT-END
1 Affected Product
Vehicle
MAKE | MODEL | YEAR |
TOYOTA | SIENNA | 2019 |
11 Associated Documents
ISSUED Owner Notification Letter(Part 577)
RCONL-19V318-6533.pdf 62.344KB
April 23, 2019 DEFECT INFORMATION REPORT
RMISC-19V318-2676.pdf 31.977KB
Manufacturer Notices(to Dealers,etc)- SAFETY RECALL K0G (Interim Notice K1G)
Recall Acknowledgement
RCAK-19V318-3311.pdf 245.815KB
Defect Notice 573 Report
RCLRPT-19V318-2269.PDF 213.843KB
Manufacturer Notices(to Dealers,etc)- SAFETY RECALL K0G (Interim Notice K1G)
RCMN-19V318-9784.pdf 208.608KB
Manufacturer Notices(to Dealers,etc)- SAFETY RECALL K0G (Remedy Notice)
RCMN-19V318-2606.pdf 902.298KB
Remedy Instructions and TSB
RCRIT-19V318-3431.pdf 1186.899KB
Recall Quarterly Report #2, 2019-3
RCLQRT-19V318-4516.PDF 211.255KB
Recall Quarterly Report #3, 2019-4
RCLQRT-19V318-1882.PDF 211.345KB
Recall Quarterly Report #1, 2019-2
RCLQRT-19V318-9488.PDF 211.152KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V318&docType=RCL
- 【Buy with Confidence】 As a America's No.1 diagnostic tool brand, Innova stands for innovation, quality, and accessibility in the automotive diagnostic industry. We are known for developing cutting-edge diagnostic tools that are user-friendly, reliable, and made for US by Americans.
- 【Unleash Your Drive's Potential】Much more than a car code reader, the 6100P scanner effectively reads and erases engine, ABS, SRS, and transmission codes for popular US car makes such as Ford, Chevy, Dodge, GM, etc. When the traction light is constantly on, the ability to really detect where the problem is concerning brakes and airbags enables you to make sure all safety measures in place before putting yourself in harm's way.
- 【Your Car's Health Doctor】Easily view procedures or send commands for oil change, mileage or driving time reset for most 1996 and newer OBD2 vehicles. It also monitors your oil level and oil life status, ensuring optimal vehicle health.
- 【alternator Test】The Innova 6100P scanner is perfect for assessing the performance of the alternator in your hybrid, car, SUV, minivan, or light truck diesel as well. During rough winters and scorching summers, this diagnostic tool will be invaluable when trying to root out start-up issues.
- 【Drive with Confidence and Peace】Quickly identify if your vehicle needs immediate attention with our Code Severity Levels function. This feature helps you understand whether you need to fix an issue immediately or if it can wait until you get home, keeping warning lights at bay.
- 🎉【2024 Upgraded Ver. of AL519/ ML519/ ML619】Autel develops the brand-new AutoLink AL619 as the advanced ver. of Autel ML519, AL519, AL319, MS309. This AL619 OBD2 scanner can scan ABS & SRS systems, and support 10 Modes of OBD II Diagnostics Function on Worldwide Vehicles to read, erase codes and turn off the MIL, ABS, SRS warning lights so that you can better maintain your car when related malfunctions occur and make your vehicle ready for the annual test.
- 🎉【Accurate ABS/ SRS Diagnostics Functions】The ABS/ SRS diagnostic function is used to retrieve and clear codes from the ABS/ SRS systems. It can read and clear DTCs, show definitions of each code, display live data of multiple sensors in the graph to locate fault causes, and assist home mechanics to do the proper repair and clear ABS & Airbag warning lights. Diagnoses ABS/ SRS system codes on most 1996 and newer major vehicle models. Please email 📩 immoautel @ outlook. com 📩 for help.
- 🎉【All 10 Modes of OBD II Diagnostics Function】The OBD II Diagnostics function is a fast-access option that allows you to carry out a quick test on the engine system of OBD II vehicles. Read Codes, Erase Codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, DTC Lookup, Component Test, Viewing Vehicle Information, Modules Present.
- 🎉【Live Data and Freeze Frame Data】With Live Data functions, Autel AL619 OBD2 diagnostic code reader allows you to view the live PID (Parameter Identification Data) of the vehicle's computer module(s) in text, graph to check the status of various sensors. And Freeze Frame Data enables you to view the vehicle's operating parameters at the moment a DTC is detected. These information will aid the technician by allowing the parameters to be duplicated for diagnostic and repair purposes.
- 🎉【DTC Lookup Feature】Besides showing you the code’s definition while you are reading the diagnostic trouble codes, AL619 features comparably user-friendly DTC Lookup Function which enables you to retrieve the definitions of any error codes from the large database of AL619, saving you from the hassle of wasting time searching definition of every code via Google.
- 5 IN 1 DIAGNOSTIC SCANNER: This is an OBDII scanner and 4 systems diagnostic tool. The AUTOPHIX 3210 PRO Bluetooth Auto Scanner not only has OBDII diagnostic function, but can also be used as an ABS/SRS/transmission scanner and check engine code reader. When it is an OBD2 scanner, you can use it to check if your car is ready for annual test via I/M preparation menu. In addition, the built-in DTC library, live data stream, data playback, performance testing and many more such functions are supported by it.
- RELIABLE CAR HEALTH MONITOR: Are you confused when the ABS/SRS/Transmission/Check Engine warning light is blinking? The AUTOPHIX 3210 PRO Bluetooth Scanner will help you to do a thorough scanning and inspecting of your car and find out the root cause, which saves your time and money. Tip:The warning light will be turned off after the problem is solved. Airbag crash/collision data cannot be cleared, even if you replace the airbag with a new one.
- QUICK DIAGNOSIS: The 3210 PRO is the newest 2024 Enhanced 4-System Bluetooth Code Reader that retrieves vehicle information, reads/clears trouble codes, and displays a 4-in-1 live data stream. You'll easily find out what's wrong with your car. In just a few minutes, you'll be in control of your car!
- EXCLUSIVE APP: Are you tired of the following with third party apps? For example: 1.need to download different apps for different cars? 2. require extra download fees? 3. only support a few functions? 4. can only use one of Android and iOS? Now!One AUTOPHIX 3210 PRO Scanner is enough to solve all the above problems. The must-have wireless/bluetooth automotive diagnostic tool/code reader for today's car owners. iPhone iOS, iPad, Android can be downloaded for free without any additional subscription fees.
- ADVANCED DATA FLOW DISPLAY:AUTOPHIX 3210 PRO Bluetooth code reader allows you to graphically display your vehicle's data flow instead of boring text, including engine coolant temperature, engine RPM, vehicle speed, absolute throttle position, control module voltage, etc. You can view different parameter values corresponding to different times. The advanced data streams provide useful information for entry-level professionals and diyers who can troubleshoot vehicle problems quickly and efficiently.
- 🎄【Easy to Use--Work out of box】+【FOXWELL 2024 New Version】 FOXWELL NT604 Elite scan tool is the 2024 new version from FOXWELL, which is designed for those car owners who want to figure out the cause issue before fixing the car problem via scanning the most common systems like abs srs engine and transmission.The NT604 Elite diagnostic tool comes with latest software, which can be used out of box. No need to waste time to download the software first.
- 🎅【Affordable】+【Reliable Car Health Monitor】 Will you be confused what happen when the warning light of abs/srs/transmission/check engine flashes? Instead of taking your cars to dealership, this foxwell scanner will help you do a thorough scanning and detection for your cars and pinpoint the root cause. It will t-urn off the warning light car after the problem is fixed.👉TIPS: Airbag crash/collision data can NOT be cleared even you replace the new airbag.
- 🎄【5 in 1 Diagnostic Scanner】Compared with those auto scanners (50-100), NT604 Elite code scanner not only includes their OBDII diagnosis but also it can be an abs/srs scanner, transmission and check engine code reader. When it’s an odb2 scanner, you can use it to check if your car is ready for annual test through I/M readiness menu. In addition, live data stream, built-in DTC library, data play back and print, all these features are a big plus for it.
- 🎅【Fantastic AUTOVIN】+【No extra software fee】Through the AUTOVIN menu, this NT604 Elite car scanner allows you to get your V-IN and vehicle info rapidly, no need to take time to find your V-IN and input one by one. What's more, the NT604 Elite abs srs scanner supports 60+ car makes from worldwide (America/Asia/Europe). You don’t need to pay extra software fee.
- 🎄【Solid protective case KO plastic carrying bag】+ 【Lifetime update】Almost all same price-level obd scanner diagnostic tool only offers plastic bag to hold on the scanner.However, NT604 Elite automotive scanner is equipped with solid protective case, preventing your obd2 scanner from damage. Then you don’t need to pay extra money to buy a solid toolbox.
- 2024 Best Choice for ABS Bleeder Scan Tool - Was the brake pedal always slowly sinking down or becoming loose? This abs brake bleeding scan tool will bleed the brake system by cycling the pump and valves to achieve a tight brake pedal. It's the most affordable obd2 scanner with abs auto bleed function you can find. With the clear step by step instruction, even a beginner can use it. Coverage check on FOXWELL official site: Support- Diagnostic Coverage List.
- More Than a Entry Level OBD Scanner, Ideal for Home Mechanics - Based on the NT301 FOXWELL Scanner, NT630 Plus takes OBD diagnostics to the next level by customizing all functions for ABS and SRS systems. This srs abs scanner provides in-depth insights on error code diagnosis, wheel speed sensor live data, airbag circuits and cable connectors monitor, module activation and etc. It's an total game-changer in resolving ABS SRS issues.
- No More Higher End Service than You Needed - One NT630 Plus is enough! This obd2 scanner with abs and srs takes depth diagnosis on Anti-Lock Brake System & Supplemental Restraint System, and also performs daily required resetting services which same priced scanners cannot do. Like Airbag light reset/ SAS(Steering Angle Sensor) adjustment/ Oil light reset and EPB service functions. this car scanner will help the part to operate normally after the faults repaired.
- Also can Work like NT301 - The NT630 Plus abs code reader connect to the OBD2 port directly. It will diagnose all obd2 modules instantly, displays the live data, locates bad sensors and I/M readiness status before the annual inspection. Guides you to do the maintenance work, reduces the potential driving risk and keep a peak performance on the road.
- Complicate? Unreadable? - Intuitive LCD display with clear operate instructions, even a beginner can diagnose the car faults with the NT630 Plus. Ergonomic Touch with anti-collision and anti-slip cover design, comfortable for daily car diagnose work. Unique button press sound will provide the overall tactile and visual experience to notice you a task has been completed or a command has been executed.
- 💻Note: (About UPDATE) ANCEL FX2000 car scanner diasgnostic tool can be used directly as it comes with existed software, You don't need to register or update beforethe first use. It's recommended to update your scanner only when it fails to work on your car, or it's slow to load all menus or if you need newer software version. 📢Software update supports WIN XP, 7, 8, 10 operation systems only., but not for Mac and ios system.
- 🔧【PLUG AND PLAY - EASY TO USE】 : ANCEL FX2000 car scanner only takes 3 steps to connect to the car for diagnosis without cumbersome operations. The latest FX2000 scan tool is equipped with a one-key diagnosis function, which can automatically identify the model and year of your car, and automatically diagnose the car. Even beginners can use it to read the data and find out what the fault codes mean.
- 🚗【FULL OBD-LEVEL DIAGNOSTICS TOOL】: Quickly determines the cause of engine system faults, reads current, permanent and pending codes. After the repair, clears the codes and turns off the warning light. In addition, the FX2000 engine code reader also displays important OBD II advanced data such as fuel, live data and other manufacturer-specific parameters in real time to ensure that the engine ECU is operating correctly and safely, saving vehicle owners a lot of time and money in maintenance.
- 🚙【TRANSMISSION FAULT DIAGNOSTIC TOOL】: Some noises come from the transmission? Ancel obd2 scanner will read fault codes, display live transmission system data (fluid temperature, fluid pump, clutch actuation, pressure, etc.), and ensures transmission performance is optimal for vehicle speed and load. It provides detailed TCM data of the vehicle, so you can quickly and accurately find existing or potential problems.
- 🚐【FIND OUT SRS WRONG】: ANCEL FX2000 automotive scanner is able to read and clear fault codes in the SRS (airbag) and turn off the warning light to make sure the system is working correctly and safely. This odb2 scanner also displays a live graphical data stream of the supplemental restraint system (air bag), which allows you to analyze and verify that the air bag system is working properly.
- [Transform Your Car Care Experience] - With BLCKTEC, instantly become your own professional mechanic. Effortlessly read and clear your car’s trouble codes and check engine light, ensuring your vehicle stays in top condition.
- [Empower Yourself with Comprehensive Diagnostics] - Unlock the full potential of your vehicle with the BLCKTEC 430. Access detailed diagnostics previously exclusive to professional mechanics’ OBD2 scan tools, including ABS, Airbag, SRS, TPMS codes, and beyond, right at your fingertips.
- [Drive with Confidence] - The BLCKTEC 430 is more than just a car code reader; it's your personal vehicle health advisor. Receive tailored repair reports with potential causes and verified solutions for your specific make and model, guiding you to the right fix every time.
- [Seamless Connectivity, Ultimate Convenience] - Experience the freedom of wireless diagnostics with this portable car scanner. Easily connect via Bluetooth to our intuitive sensor, and enjoy all the functionalities of high-end scan tools without the clutter of wires, directly from your smartphone or tablet.
- [DIY Repairs Made Easy] - Navigate car maintenance with ease using our premium app. Access a vast library of easy-to-follow repair videos, guiding you through each step of the repair process, compatible with both iOS & Android devices.
- [ABS & SRS Scanner with Active Test] The ABS/ SRS diagnostic tool Read & clear DTCs, displays live data in a graph to locate the cause of faults and assists the home mechanic with repairs and clearing ABS and airbag warning lights. Active test sensors, valves or solenoids etc. and tracks any threats in real time. It is invaluable to have a diagnostic tool with Active Test feature that you will never find on similar ABS/ SRS scanners.
- 【3 HOP Reset Services 】Easy to set up 3 regular reset services for Oil Light, Battery Management System, and Steering Angle Position. With this obd2 scanner, you can reset the oil service light and reset pre-programmed mileage intervals for energy efficiency; adjust or reset the steering angle position to keep steering aligned; and clear the original low battery fault information. No need to leave home for shop-quality car maintenance.
- 【All OBD2 Test Modes 】 This ABS & SRS scan tool is also a full featured obd2 code reader, allowing a quick test of the engine system of OBD II vehicles, can Read/Clear engine light codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, Evap Test, Read Vehicle Information, and help pass smog test for most post-1996 OBD2/CAN vehicles.
- [DTC LookUp Library] Can't read the code? Go to the DTC LookUp Library. The Topdon AL600 OBD2 scanner offers a wealth of code definitions so you don't have to look them up in a list or database, and the HELP function takes you to diagnostic tips for possible fixes, saving time searching for repair materials online. No other scan tool or code reader under $100 offers this level of assistance.
- [User-Oriented] You'll love the feel of this automotive scanner, with black rubber grips all around the outer edges for durability and to withstand accidental drops. With its easy access menu, you can operate all functions in minutes with just a few button presses. The 3-color LEDs give you a intuitive indication of the OBD2 test results in a second. 3 shortcut keys, one key to read/clear DTCs and a one-touch smoke status check make it easy to use even for beginners.
- [OBD2 Scanner] The TOPDON OBD2 scanner performs all ENG/AT/SRS/ABS diagnostics with 4-in-1 graphic live data. 🚩It covers all OBD2 tests for 67 manufacturers and 10000+ model. It also features 5-second one-touch AutoVIN, 🚩a free one-touch lifetime upgrade through WiFi, library DTC, 12 languages, 🚩printable auto-generated report with email sharing, 🚩smooth Android 11.0, 32GB ROM, 🚩vivid 5-inch touchscreen, and up to 10 hours of battery life.
- [4 Car System Code Reader] The TOPDON OBD2 scanner accesses 4 systems: 🚩Engine/ABS/SRS/Transmission. It identifies the ECU version, pull DTCs with 4-in-1 graphic live data and DTC explanation to identify issues, erase DTCs to turn off the warning lights after repair (For cars made in 2005 and newer). In order to help you extend the lifespan of your vehicle while improving performance, this code reader also includes all obd2 test modes to solve the major concerns for all vehicles.
- [User-Oriented TOPDON OBD2 Scanner] With this scan tool's touchscreen and rubberized buttons, you may easily navigate through menus or process while following a logical path. With 32GB on-board memory, the scanner enables for the recording of several diagnostic reports, which can be shared via email and printed for review. Along with this, you can 🚩upgrade your software for free for lifetime with one-touch over Wi-Fi for that help update the features and expanding car coverage.
- [Multiple Functions] The Smart AutoVIN of this TOPDON OBD2 scanner keeps track of your manual selections for vehicle make, model, and year and directs you to the suitable diagnostics. 🚩Max 4 Live Data streams integrated for much easier data processing. Diagnostic feedback online with this diagnostic tool to help you get tough repair operations well-completed. Real-time car battery voltage monitoring identifies probable vehicle defects.
- [Wide Coverage] With its multilingual menu and 🚩coverage of 67 car brands and 10,000+ models spanning North America, Europe, and Asia (including Malaysia, India, and Iran), this car scanner is compatible with the majority of 1996 and newer OBDII compliant automobiles (EN, FR, ES, DE, IT, RU, PT, JP, KR). Before buying, make sure the OBD2 scanner is compatible with your vehicle. The package contains only a charging cable and not a power adapter.
- [COMPATIBLE FOR BMW] - As what you've seen, we have a variety of OBD2 code readers compatible for BMW and MINI, C410 is one of the most cost-effective scan tools fit for BMW and MINI vehicle owners. C410 Supports most BMW and MINI after 2001. 1997-2004 cars need a 20 pin adaptor (not included).
- [FIT FOR BMW AND MINI] - Compatible ECU systems including Drive, Chassis and Body all system. Supported function including read and clear trouble codes, display live data stream, graph display, vehicle version information, clear adaptation, CBS reset and reset Engine oil.
- [EASY TO OPERATE] - C410 car diagnostic tool via 2.4" TFT 240K true color LCD display screen to indicates the test results , with the silicone keypad you can easy to access the each of menu options, Rugged drop-proof case Prevent falling, the menu layout on the screen is easy to understand and you will no trouble to figuring out how to do what you needed.
- [LIFETIME FREE UPDATE] - Many OBDII scanners for BMW require to pay an additional fee for new upgrades after the warranty period has expired. C410 supports lifetime free software upgrades, new parameters, functions and the latest vehicle data are constantly updated via the USB port over the Internet. Just a few easy steps, the scanner will always be up to date with the latest system within minutes.
- [ATTENTION PLEASE!!!] - Battery registration function does not support cars before 2004 and also does not support the E chassis (3 Series_E46, 5 Series_E39, 7 Series_E38, X3_E83, X5_E53, Z3_E36, Z4_E85/E86, MINI_R50/R51/R52/R53). For the above chassis models, you just need to replace the battery directly, because these models do not require battery registration. In addition, the battery registration function only for the same type and capacity battery. Inconsistent battery type or capacity can lead to registration failure.
Last update on 2024-03-22 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.