Safety Recall SET19B – Torque Verification on Various Components – 2018-2019 Toyota 4Runner

“This site contains affiliate links for which OEMDTC may be compensated”

September 20, 2019 NHTSA CAMPAIGN NUMBER: 19V670000

Improperly Tightened Steering/Suspension Fasteners

Loose fasteners may cause a loss of vehicle control, or cause an accessory to detach from the vehicle and become a road hazard. Either of these scenarios can increase the risk of a crash or injury.

 

NHTSA Campaign Number: 19V670

Manufacturer Southeast Toyota Distributors, LLC

Components STEERING, SUSPENSION

Potential Number of Units Affected 34

 

Summary

Southeast Toyota Distributors, LLC (SET) is recalling certain 2018-2019 Toyota 4Runner vehicles. During installation, certain steering and suspension components may not have been properly tightened.

 

Remedy

SET will notify owners, and dealers will inspect and re-tighten the steering and suspension fasteners as necessary, free of charge. The recall is expected to begin November 19, 2019. Owners may contact SET customer service at 1-866-405-4226. SET’s number for this recall is SET19B.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 

Check if your Vehicle has a Recall

 


Attention

This is an important Safety Recall which was initiated by Southeast Toyota Distributors, LLC.

If you are in Florida, Georgia, Alabama, South

Carolina, or North Carolina, please refer to SET Dealer Daily to obtain instructions on how to complete this repair and submit a warranty claim.

Toyota Dealerships outside of Florida, Georgia, Alabama, South Carolina or North Carolina

SET will reimburse you for the repairs outlined in the following procedure.  For repair authorization and parts ordering, please contact Southeast Toyota Distributors, LLC toll free at 1-888-851-2722, or email oordealersupport@setoyota.com.

Thank you for your continued support.

Southeast Toyota Distributors, LLC


To: All Toyota Dealer Principals, General Managers, Service Managers, and Parts Managers

Subject: Safety Recall SET19B – Remedy Available

On September 20, 2019 Southeast Toyota Distributors, LLC (SET) filed a Defect Information Report (DIR) with the National Highway Traffic Safety Administration (NHTSA) initiating a Safety Recall on certain 2018 -2019 Toyota 4Runner vehicles equipped with TRD accessories installed by SET.

 

Affected Vehicles:

2018 – 2019 Toyota 4Runner vehicles equipped with TRD accessories installed by SET.

 

Condition:  

During an audit SET found that some accessory fasteners may not have been tightened to a specified torque.  If the fasteners are not properly tightened to the specified torque, the fastener could become loose, possibly causing loss of control of the vehicle or the accessory could detach from the vehicle, which could cause a crash or injury.

 

Remedy

All known owners of the affected vehicles will be notified by US mail to return their vehicles to a Toyota dealer.  The Toyota dealer will, inspect and tighten the affected fasteners with a torque wrench pursuant to instructions specified by SET, at no cost to the owner.

This following information is being provided to keep you informed of the filing and your degree of involvement.

 

1. Owner Letter Mailing Date

SET has completed remedy preparations and will begin to notify owners on or before November 19, 2019.

SET makes significant effort to obtain current customer name and address information when mailing owner letters.  In the event your dealership receives a notice for a vehicle that was sold prior to the Safety Recall announcement, it is the dealership’s responsibility to forward the owner letter to the customer who purchased the vehicle.

 

2. New Vehicles in Dealership Inventory

Red Stop

Under Title 49, Section 30112(a) of the United States Code, a dealer cannot sell, offer for sale, or introduce or deliver for introduction in interstate commerce a new motor vehicle when it is aware that the vehicle does not comply with an applicable Federal Motor Vehicle Safety Standard.  In addition, 49 Code of Federal Regulations §577.13 requires us to provide the following advisory:  it is a violation of Federal law for a dealer to deliver a new motor vehicle or any new or used item of motor vehicle equipment (including a tire) covered by this notification under a sale or lease until the defect or noncompliance is remedied.

Vehicle Safety Recall completion can be verified through TIS.  Additional information will be provided as it becomes available. 

 

3. Inspection Reminder Mirror Hang Tags for Covered Vehicles

To easily recognize vehicles involved in this Safety Recall, each dealership should utilize Inspection Reminder Hang Tags. Please reference the VIN list provided to identify new vehicles in dealer inventory involved in this Safety Recall. Inside the vehicle’s glove box are stickers containing the VIN.  Apply one of these stickers to the hang tag and install the hang tag in the vehicle. A sample copy of the Inspection Reminder Hang Tag has been included for your reference.

Hold For Inspection

Note: Dealerships can order Hang Tags from the Material Distribution Center (MDC).

Part Number Description Qty.
00411-140003 Inspection Mirror Hang Tag (25 Per Pack)

 

 

4. Pre-Owned Vehicles in Dealer Inventory

SET requests that dealers do not deliver any pre-owned vehicles in dealer inventory that is covered by a Safety Recall unless the defect has been remedied.

 

5. Dealer Summary Reports

Please verify eligibility by confirming through TIS and inspecting the vehicle prior to performing repairs.

 

6. Number and Identification of Covered Vehicles

There are approximately 34 vehicles covered by this Noncompliance Recall in the U.S. and Puerto Rico.

Please note that only owners of the covered vehicles will be notified. If a dealer is contacted by an owner who has not yet received the notification, please instruct the dealer personnel to verify coverage by confirming through TIS and inspecting the vehicle.  Dealers should perform the procedure as outlined in the Technical Instructions located on TIS.

 

7. Parts Ordering 

Part Number Part Name Qty
N/A N/A N/A

 

8. Technician Training Requirements

All dealership technicians performing this recall are required to successfully complete the most current version of E-Learning course “Safety Recall and Service Campaign Essentials”. To ensure that all vehicles have the repair performed correctly; technicians performing this recall are required to have successfully completed E-learning course SC18A (if you had previously completed E-learning Course SC13B, you do not have to take SC18A), in addition to “Safety Recall and Service Campaign Essentials”, and currently hold at least one of the following certification levels:

  • Toyota Expert
  • Master
  • Master Diagnostic Technicians

  

9. Remedy Procedures 

Please refer to TIS for Technical Instructions on repair.  Conduct all applicable, non-completed Safety Recall and Service Campaigns on the vehicle during the time of appointment.

 

10 Warranty Reimbursement Procedure 

Certain 2018 – 2019 Toyota 4Runner vehicles equipped with TRD accessories installed by SET
Warranty Reimbursement Procedure

 

SET vendor warranty claim should be submitted as follows:

OP CODE DESCRIPTION TIME OFP T1 T2
AR19B1 Accessory Torque Validation 2.0 00016-SPECL 99 99
Additional Claim information:
Replacement Parts: N/A, leave blank
Sublet: N/A, leave blank
Condition: SET19B
Cause: SET19B
Remedy: Perform Torque Validation
Claim Attachment: SET19B Torque Validation Form must be attached to AW CPS claim.

 

The flat rate times include 0.1 hours for administrative cost per unit for the dealership.

 

If you are a dealer located outside of the Southeast Region, email oordealersupport@setoyota.com attach copy of RO invoice for payment processing.

 

 

Campaign Designation Decoder 

Campaign Designation Decoder
Examples:

SET14A = Launched in 2014, Remedy Phase, 1st Campaign Launched in 2014

SET14B = Launched in 2014, Remedy Phase, 2nd Campaign Launched in 2014

SET15A = Launched in 2015, Remedy Phase, 1st  Campaign Launched in 2015

 

11. Repair Quality Confirmation

Not required for this Recall.

 

12. Technical Questions

If you are a SET dealership associate and have any questions, please contact your Field Technical Specialist. If your dealer is outside the Southeast Toyota Region and have technical questions please contact SET at 1-888-851-2722, press 6 for recall support.

 

13. Media Contacts

In the event you are contacted by the News media, it is imperative that all media contacts (local and national) receive a consistent message. In this regard, all media contacts must be directed to SET Corporate Communications 954-363-6285. (Please do not provide this number to customers.)

 

14. Customer Contacts

A FAQ is attached to help respond to any customer concerns.  If the customer has any further questions, they are requested to contact the Southeast Toyota (SET) Customer Relations Center at 1-866-301-6859, press 1 for Southeast Toyota and SET will return the call within 24 hours between 8:30 am and 5 pm eastern standard time.

Please review this entire package with your Service and Parts staff to familiarize them with the proper stepby-step procedures required to implement this Safety Recall.

 

Thank you for your cooperation

Southeast Toyota Distributors, LLC.


4RUNNER TORQUE RECALL-SET19B
QUESTIONS & ANSWERS

Certain Model Year 2018 through 2019 4Runner vehicles equipped with TRD accessories installed by SET.

Background: On September 20, 2019 Southeast Toyota Distributors, LLC. (“SET”) filed a Defect Information Report with the National Highway Traffic Safety Administration (NHTSA) informing the agency of its intent to conduct a voluntary Safety Recall on certain 2018 through 2019 4Runner vehicles equipped with TRD accessories installed by SET.  There are approximately 34 vehicles covered by this recall.

Affected Vehicles: Certain 2018 through 2019 4Runner vehicles equipped with TRD accessories installed by SET.

1. What is the condition?

During an audit SET found that some accessory fasteners may not have been tightened to a specified torque.  If the fasteners are not properly tightened to the specified torque, the fastener could come loose, possibly causing loss of control of the vehicle or the accessory could detach from the vehicle, which could cause a crash or injury.

 

2. Why are only certain vehicles covered by this Safety Recall?

SET undertook an investigation to determine the scope of the issue and the potential consequence.  The investigation found that the issue was limited to the use of a specific model of torque wrench at a specific location.

The audit indicated that 34 vehicles were missing torque validation data.

 

3. How many vehicles are involved?

SET estimates that approximately 34 vehicles are affected by this recall.

4. Are there any other Toyota vehicles affected?

No, there are no other Toyota vehicles affected.

 

6. What is SET going to do?

All known owners of the affected vehicles will be notified by US mail to return their vehicles to a Toyota dealer.  The Toyota dealer will, inspect and tighten the affected fasteners with a torque wrench pursuant to instructions specified by SET, at no cost to you.

 

7. Is there any cost?

These actions will be performed at no charge.

 

8. How long will the process take?

The corrective action will take approximately one hour or less.  However, depending upon the dealer’s work schedule, it may be necessary for the owner to make the vehicle available for a longer period of time.

 

9. Is my vehicle covered by this Safety Recall?

Owners of the affected vehicles will receive a Safety Recall letter from Southeast Toyota Distributors, LLC informing them of this safety recall campaign.  In the meantime, owners may contact any Toyota dealer to verify if their vehicle is covered by this campaign.

 

10. What if an owner has additional questions or concerns?

Owners with questions or additional concerns are asked to contact the Southeast Toyota Distributors, LLC.  SET Customer Assistance Center toll free at 1-800-301-6859 Monday through Friday, 8:30 am to 5:00 pm Eastern Standard Time.


Attention

This is an important Safety Recall which was initiated by Southeast Toyota Distributors, LLC.

If you are in Florida, Georgia, Alabama, South

Carolina, or North Carolina, please refer to SET Dealer Daily to obtain instructions on how to complete this repair and submit a warranty claim.

Toyota Dealerships outside of Florida, Georgia, Alabama, South Carolina or North Carolina

SET will reimburse you for the repairs outlined in the following procedure.  For repair authorization and parts ordering, please contact Southeast Toyota Distributors, LLC toll free at 1-888-851-2722, or email oordealersupport@setoyota.com.

Thank you for your continued support.

Southeast Toyota Distributors, LLC


TECHNICAL INSTRUCTIONS
FOR
VOLUNTARY SAFETY RECALL CAMPAIGN SET19B
TORQUE VERIFICATION ON VARIOUS COMPONENTS
CERTAIN 2018-2019 MODEL YEAR 4RUNNER

 

All dealership technicians performing this recall are required to successfully complete the most current version of ELearning course “Safety Recall and Service Campaign Essentials”. To ensure that all vehicles have the repair performed correctly; technicians performing this recall are required to have successfully completed E-learning course SC18A (if you had previously completed E-learning Course SC13B, you do not have to take SC18A), in addition to “Safety Recall and Service Campaign Essentials”, and currently hold at least one of the following certification levels: 

  • Toyota Expert
  • Master
  • Master Diagnostic Technicians

 

OPERATION FLOW CHART

Warranty Reimbursement Procedure

 

IDENTIFICATION OF AFFECTED VEHICLES

NOTE: 

  • Check the TIS Vehicle Inquiry System to confirm the VIN is involved in this SSC and that the campaign has not already been completed prior to dealer shipment or by another dealer.
  • Southeast Toyota warranty will not reimburse dealers for repairs conducted on vehicles that are not affected or were completed by another dealer.

 

PREPARATION

A. PARTS

None required

 

B. TOOLS & EQUIPMENT

  1. Digital Torque wrench
  2. Standard hand tools

 

BACKGROUND

SET’s investigation found that a specific model of Atlas Copco Torque wrench utilized in the 4Runner accessory line was failing to consistently upload the torque data to the Atlas Copco system due to poor Wi-Fi connectivity at the Talleyrand facility.  This recall is to confirm that accessories installed with this torque wrench were properly torqued to the installation specifications.

 

WARRANTY INFORMATION

For Dealers located in the Southeast Region, Florida, Georgia, Alabama, South Carolina, or North Carolina, Submit Warranty claim utilizing the information below.

OP CODE DESCRIPTION TIME OFP T1 T2
AR19B1 Accessory Torque Validation 2.0 00016-SPECL 99 99
Additional Claim information:
Replacement Parts: N/A, leave blank
Sublet: N/A, leave blank
Condition: SET19B
Cause: SET19B
Remedy: Perform Torque Validation
Claim Attachment: SET19B Torque Validation Form must be attached to AW CPS claim.

 

The flat rate times include 0.1 hours for administrative cost per unit for the dealership.

If you are a dealer located outside of the Southeast Region, email oordealersupport@setoyota.com attach copy of RO invoice for payment processing.

 

WORK PROCEDURE

Note: SET19B Instructions outline a process which requires the SET19B Torque Validation Form located at the end of this document be completed. SET requests this form be scanned and attached to the SET warranty claim. 

  1. Lift vehicle on suitable hoist.
  2. Remove Tire and Wheel assemblies from vehicle.
  3. Remove TRD skid plate from front of vehicle. (Fig. 1)
    1. Use a 14mm socket to remove the two rear bolts and loosen the two front bolts attached to the Skid Plate. Remove the Skid Plate and retain it and the bolts for reinstallation.

 

  1. Verify torque of left and right side Upper Shock Nuts, Items A1A6 on SET19B Torque form.
    1. Use a 14mm crowfoot to torque the nuts on the upper side of the front shock absorber with coil spring assembly (Refer to Fig. 2).
    2. Set torque wrench higher than upper range limit.
    3. Slowly apply torque until the fastener starts to rotate.
    4. Document reading on SET19B Torque form under initial values.
    5. If any measurement is out of specified range: loosen, retorque to specified value. Record values on SET19B torque form.
  • Torque, with crowfoot:
    • Range: 56-93 N-m (41-69 ft-lbf)
    • Specified: 65 N·m (663 kgf·cm, 48 ft·lbf)
  • Torque, without crowfoot:
    • Range: 62-102 N-m (46-75 ft-lbf)
    • Specified: 71 N·m (724 kgf·cm, 52 ft·lbf)
  1. Verify torque of the left and right lower ball joint attachment bolts (Fig. 3). Items B1-B4 on SET19B Torque form.
    1. Use a 19mm socket to torque bolts.
    2. Set torque wrench higher than upper range limit.
    3. Slowly apply torque until the fastener starts to rotate.
    4. Document reading on SET19B Torque form under initial values.
    5. If any measurement is out of specified range: loosen, retorque to specified value. Record values on SET19B torque form.
  • Torque:
    • Range: 139-229 N-m (103-169 ft-lbf)
    • Specified: 160 N·m (1631 kgf·cm, 118 ft·lbf)
  1. Verify torque of left and right side front lower control arm Bolts (Fig. 4) Items C1-C4 on SET19B Torque Form.
    1. Use a 22mm socket to torque the front and rear lower control arm bolts (Fig. 8-2).
    2. Set torque wrench higher than upper range limit.
    3. Slowly apply torque until the fastener starts to rotate.
    4. Document reading on SET19B Torque form under initial values.
    5. If any measurement is out of specified range: loosen, retorque to specified value. Record values on SET19B torque form.
  • Torque:
    • Range: 152-251 N-m (112-185 ft-lbf)
    • Specified: 175 N·m (1785 kgf·cm, 129 ft·lbf)
  1. Verify Torque of driver side and passenger side tie rod end locking nuts. (Fig. 5) Items D1 and D2 on SET19B Torque Form.
    1. Use a 22mm crowfoot to torque the front and rear lower control arm bolts.
    2. Set torque wrench higher than upper range limit.
    3. Slowly apply torque until the fastener starts to rotate.
    4. Document reading on SET19B Torque form under initial values.
    5. If any measurement is out of specified range: loosen, retorque to specified value. Record values on SET19B torque form.
  • Torque:
    • Range: 76-126 N-m (56-93 ft-lbf)
    • Specified: 88 N·m (897 kgf·cm, 65 ft·lbf)
  1. Verify Torque of driver side and passenger side front lower shock bolts. (Fig. 6) Items E1 and E2 on torque Form.
    1. Use a 19mm wrench and 19mm socket to torque the front lower shock bolts.
    2. Set torque wrench higher than upper range limit.
    3. Slowly apply torque until the fastener starts to rotate.
    4. Document reading on SET19B Torque form under initial values.
    5. If any measurement is out of specified range: loosen, retorque to specified value. Record values on SET19B torque form.
  • Torque:
    • Range: 82-136 N-m (61-100 ft-lbf)
    • Specified: 95 N·m (969 kgf·cm, 70 ft·lbf)
  1. Reinstall TRD skid plate and verify Torque. (Fig. 7)
    1. Use a 14mm wrench torque the front lower shock bolts.
      • Torque: 30 N·m (306 kgf·cm, 22 ft·lbf)
    2. Document Torque on SET19B Torque form.
      • F1-4 for skid plate
  1. Verify Torque of driver side and passenger Rear lower shock bolt. (Fig. 8) Items G1 and G2 on torque Form.
    1. Use a 19mm socket to torque the front lower shock bolts.
    2. Set torque wrench higher than upper range limit.
    3. Slowly apply torque until the fastener starts to rotate.
    4. Document reading on SET19B Torque form under initial values.
    5. If any measurement is out of specified range: loosen, retorque to specified value. Record values on SET19B torque form.
  • Torque:
    • Range: 82-136 N-m (61-100 ft-lbf)
    • Specified: 98 N·m (1000 kgf·cm, 72 ft·lbf)
  1. Reinstall tire and wheel assemblies (Fig. 9)
    1. Torque lug nuts to specification
      • Torque: 103 N·m (76 ft·lbf)
    2. Document Lug Nut Torque on Torque record form.
  1. Review Torque form to verify completion.
    1. Dealer should retain a copy with the RO.
    2. Torque form must be attached to warranty claim submitted to SET.

 

APPENDIX 

A. CAMPAIGN DESIGNATION DECODER

Campaign Designation Decoder
Examples:

SET14A = Launched in 2014, Remedy Phase, 1st Campaign Launched in 2014

SET14B = Launched in 2014, Remedy Phase, 2nd Campaign Launched in 2014

SET15A = Launched in 2015, Remedy Phase, 1st  Campaign Launched in 2015

 

SET19B Torque Validation Form VIN:
FRONT UPPER SHOCK NUTS  LEFT SIDE RIGHT SIDE
Initial Value Re-torque Value Initial Value Re-torque Value
A1: A4:
A2: A5:
A3: A6:
Note: “Re-torque Value” is only needed if the “Initial Value” is out of the range:

  • With Crowfoot: 56-93 N-m (41-69 ft-lbf)
  • Without Crowfoot: 62-102 N-m (46-75 ft-lbf)
LOWER BALL JOINT ATTACHMENT BOLTS LEFT SIDE RIGHT SIDE
Initial Value Re-torque Value Initial Value Re-torque Value
B1: B3:
B2: B4:
Note: “Re-torque Value” is only needed if the “Initial Value” is out of the range:

  • 139-229 N-m (103-169 ft-lbf)
LOWER CONTROL ARM BOLTS LEFT SIDE RIGHT SIDE
Initial Value Re-torque Value Initial Value Re-torque Value
C1: C3:
C2: C4:
Note: “Re-torque Value” is only needed if the “Initial Value” is out of the range:

  • 152-251 N-m (112-185 ft-lbf)
TIE ROD END LOCKING NUT LEFT SIDE RIGHT SIDE
Initial Value Re-torque Value Initial Value Re-torque Value
D1: D2:
Note: “Re-torque Value” is only needed if the “Initial Value” is out of the range:

  • 76-126 N-m (56-93 ft-lbf)

 

FRONT LOWER SHOCK BOLTS LEFT SIDE RIGHT SIDE
Initial Value Re-torque Value Initial Value Re-torque Value
E1: E2:
Note: “Re-torque Value” is only needed if the “Initial Value” is out of the range:

  • 82-136 N-m (61-100 ft-lbf)
TRD SKID PLATE LEFT SIDE RIGHT SIDE
Torque Value Torque Value
F1: F3:
F2 F4:
REAR LOWER SHOCK BOLTS LEFT SIDE RIGHT SIDE
Initial Value Re-torque Value Initial Value Re-torque Value
G1: G2:
Note: “Re-torque Value” is only needed if the “Initial Value” is out of the range:

  • Range:  82-136 N-m (61-100 ft-lbf)
WHEELS  LEFT SIDE RIGHT SIDE
Left Front Left Rear Right Front Right Rear

 



2 Affected Products

Vehicle

MAKE MODEL YEAR
TOYOTA 4RUNNER 2018-2019

 


11 Associated Documents

Recall Quarterly Report #2, 2020-1

RCLQRT-19V670-2424.PDF 211.245KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.29 KB]

 


Recall Quarterly Report #1, 2019-4

RCLQRT-19V670-6245.PDF 211.15KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.20 KB]

 


Recall Quarterly Report #3, 2020-2

RCLQRT-19V670-3059.PDF 211.33KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.38 KB]

 


Part 577 Owner Notification Envelope – RONE-19V670-2730

RONE-19V670-2730.pdf 27.138KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [26.50 KB]

 


Owner Notification Letter(Part 577) – SET19B- Issued Owner Notification

RCONL-19V670-8796.pdf 187.266KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [182.88 KB]

 


Defect Notice 573 Report

RCLRPT-19V670-4792.PDF 213.95KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [208.94 KB]

 


Manufacturer Notices(to Dealers,etc) – Subject: Safety Recall SET19B – Remedy Available

RCMN-19V670-6023.pdf 144.535KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [141.15 KB]

 


Recall Acknowledgement

RCAK-19V670-3654.pdf 245.33KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [239.58 KB]

 


Remedy Instructions and TSB

RCRIT-19V670-7249.pdf 977.279KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [954.37 KB]

 


Recall 573 Report – Amendment 1

RCLRPT-19V670-2313.PDF 214.033KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [209.02 KB]

 


Recall Quarterly Report #4, 2020-3

RCLQRT-19V670-9029.PDF 211.432KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [206.48 KB]

 


Latest Recalls Documents

For the Latest and Most Recent Recalls Information Visit the link below…

https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V670&docType=RCL

 


 

SaleBestseller No. 1
EPAuto 1/2-inch Drive Click Torque Wrench, 10-150 ft/lb, 13.6-203.5 N/m
  • Durable Ratchet Head: Made from Hardened treated Chrome Vanadium steel alloy (Cr-V) Corrosion-Retardant: Satin Finish. Made in Taiwan
  • Easy Storage: A sturdy plastic storage case is included. Non-Slip Grip: Knurled handle
  • Easy to Read: High Contrast & Dual Range Scale. Accurate: Pre-Calibrated to ± 4%
  • Accessories included: 1/2" Drive 5" long Extension Bar and 1/2" Drive to 3/8" Drive Reducer
  • Simple and Reliable: “Click” sound tells the preset torque value is reached. Stop applying force when you hear and feel it.
SaleBestseller No. 2
LEXIVON 3/8-Inch Drive Click Torque Wrench 10~80 Ft-Lb/13.6~108.5 Nm (LX-182)
  • PRECISION - Ships pre-calibrated to +/- 4% accuracy and ready to use. Include calibration certificate with traceable serial number.
  • DURABLE - Reinforced ratchet gear head constructed from hardened, heat treated Chrome Vanadium alloy steel.
  • LONG-LASTING - Rust & corrosion protection with our unique and newly invented Electro-Black finish treatment.
  • PERFORMANCE - Features an easy-to-read, highlighted yellow print dual-range scale. Identify the markings even in low-light conditions.
  • COMFORTABLE - Comes with a reversible ratchet head that drives in both directions and measure torque in a clockwise direction.
Bestseller No. 3
SUERCUP 3/8-Inch Drive Click Torque Wrench - 5-45 Ft-Lb/6.8-61Nm, ±3% High Accuracy Torque Wrench, Dual-Direction Adjustable 72 Tooth Click Torque Wrench for Bike, Motorcycle and Car Repair
  • 【High Precision&Quick Reading】: 3/8 torque wrench has high contrast and dual range scale( 5-45 Ft-Lb/6.8-61 Nm),making it clear and easy to read. We have professional torque wrench production technology, and after 20000 tests, the calibration error range of the torque wrench is ± 3%, making it an essential helper for you.
  • 【Safe and Reliable Operation】: Equipped with a bidirectional drive ratchet head, torque can be measured clockwise or counterclockwise. When the set torque value is reached, a "click" sound will remind you to stop applying force to prevent damage to the item due to excessive torque.
  • 【High Quality and Durable Material】: Made of hardened chromium vanadium steel alloy (Cr-V). At the same time, the bottom buckle tail plug adopts a red anodizing process to improve the product's oxidation resistance during use and enhance surface wear resistance. 72 tooth ratchet head, made of chromium molybdenum steel. High quality materials resist corrosion and are durable.
  • 【Quick Torque Setting】: Simple and fast torque setting, pull down the locking knob and hold it down to rotate to the torque you need. Release the hand and the locking knob will automatically rebound to lock the torque value. And the designer referred to the appearance of the flashlight handle and designed a non slip and labor-saving knurled handle, making it more comfortable and easy to hold when using.
  • 【Easy to Store and Widely Use】: You will receive the 3/8-inch drive click torque wrench with a sturdy plastic shell storage box, which is very delicate and durable. Torque wrench is suitable nuts and bolts on various occasions, such as bike, motorcycle, car spark, and is the best helper for you🎁. 🔔 And we provide 12 months warranty. If you have any questions, please feel free to contact us.
Bestseller No. 4
VANPO 1/4 & 3/8 & 1/2-inch Drive Click Torque Wrench, 3Pcs Torque Wrench Set 20-240in.lb, 5-45ft.lb, 20-160ft.lb, Dual-Direction Adjustable 72-Tooth Torque Wrench for Bike, Moto, Car Maintenance
  • 【3Pcs Torque Wrench Set】 The calibration error range is ±3%, each torque wrench has a calibration certificate. The 3-in-1 torque wrench set can meet your different needs. Including 1/4 inch 20-240in.lb, 3/8 inch 5-45ft.lb, 1/2 inch 20-160ft.lb.
  • 【Safe & Reliable】 When the 1/2 torque wrench reaches the preset torque value, it makes a clear "click" sound, accompanied by an obvious hand vibration that reminds you no longer to apply force, prevent damage caused. 72-tooth reversible ratchet head, it can be used both clockwise and counterclockwise directions.
  • 【Quick Release Button】 This 3/8 torque wrench has a quick release button with which accessories can easily be installed and removed, the accessories can grip and is not easy to fall down. It is more convenient to use. The torque wrench is made of CR-MO with a higher hardness.
  • 【Easy to Set】First pull down the locking knob and hold it down and then start setting the desired torque value. Release the hand and the locking knob will automatically rebound to lock the torque value. If you do not use, please set the torque key to the minimal torque value.
  • 【Widely Use】The torque wrenches can satisfy you in bicycle, motorcycle, car, truck and wheel screws, wheel nuts and in the device installation, electrical engineering, etc. We provide 12 months warranty. If you have any questions, please feel free to contact us.
SaleBestseller No. 5
CRAFTSMAN Torque Wrench, 1/2" Drive (CMMT99434)
  • PORTABILITY: Torque wrench 1/2 inch drive has a durable case for portability or storage
  • ADDED COMFORT: Bi-material handle for comfort and grip of the 1/2 torque wrench
  • HASSLE FREE USE: Locking feature adjusts quick and easily for hassle free use
  • QUICK IDENTIFICATION: Scales stamped into housing showing inch and metric torque settings
  • Meets or Exceeds ASME Specifications
Bestseller No. 6
Amazon Basics 3/8-Inch Drive Click Torque Wrench - 15-80 ft.-lb, 20.4-108.5 Nm
  • 3/8 inch drive torque wrench with 15-80 ft.-lb./20.4-108.5 Nm range; reminder: to prevent the ratchet from breaking, please do not overload the torque wrench
  • Durable ratchet head made from hardened treated Chrome Vanadium steel alloy (Cr-V); bright, full polish chrome finish wipes easily clean and resists rust and corrosion
  • High contrast and dual range scale pre-calibrated to ± 4%; tips: for precise scale adjustment, please use the imperial scale; the conversion formula between imperial scale and metric scale is 1 Nm = 8.86 in-lbs
  • Includes sturdy plastic case for storage and portability
  • NOTE: unlock before adjusting the torque value, lock after adjusting for stability of working torque; when finished, loosen locking ring and adjust to the lowest value for next use
Bestseller No. 7
TEKTON 3/8 Inch Drive Micrometer Torque Wrench (10-80 ft.-lb.) | 24330
  • Includes 1-pc. 3/8 in. drive torque wrench; Storage case; Product manual with torque conversion chart
  • Wrench emits a click that can be heard and felt when the preset value is reached
  • Permanently marked, high-contrast dual-range scale is easy to read, even in low light
  • Reversible ratchet head drives in both directions and measures torque in clockwise direction
  • Durable all-steel construction has no plastic parts to break or wear out
Bestseller No. 8
Hairich 1/2 Inch Drive Click Torque Wrench, Dual-direction Torque Wrench 10-170.0ft.lb/13.60-230.5Nm, 72-tooth Torque Wrenches with Dual Range Scales, ±3% High Precision Torque Wrench For Bike
  • ±3% HIGH PRECISION AND COOL APPEARANCE: 1/2 inch drive torque wrench (10-170ft.-lb/13.6-230.5Nm)has a calibration error range of ±3%, high precision, and comes with a corresponding serial number, which is easy to trace the original data, and you can use it with confidence.Hairich torque wrench not only has superior quality but also has a superior appearance. The classic combination of black and red is fashionable and textured, allowing you to enjoy a visual feast during use.
  • PREMIUM MATERIAL AND DURABLE: Experience the ultimate durability and antiskid with the torque wrench. The main body of Hairich torque wrench set is made of chrome vanadium steel alloy, which is more strong and more durable. The head of the inch-pound torque wrench adopts a ratchet design with a reversing device to improve work efficiency. The square knurled handle is made of aluminum titanium alloy, which is ergonomic and comfortable to hold for long-time use.
  • DUAL SCALE AND QUICK SETTING: Laser Printed by dual-range(ft-lb and Nm). Our professional torque wrench is easy to read and provides direct unit conversion, When the set torque value is reached, the torque wrench will make an audible and felt click to remind you to stop applying force. Pull down the lock knob and hold it until the torque setting is completed. Release the hand, and the lock knob will automatically rebound back to lock the value.
  • ERGONOMIC DESIGN AND POWERFUL: Every design of our industrial torque wrench conforms to ergonomic, easy to handle.72-tooth ratchet, 5° ratcheting arc head, a quick-release button for easy loading and unloading, and an aluminum non-slip handle for excellent grip and control. A recent research review that, 72-tooth ratchets are very professional tooth ratchets, you just only rotate 5 degrees to finish it. Not easy to slip and wear, can be used in small spaces, and is more durable and powerful.
  • EASY OPERATION AND SAFETY: Thanks to its bidirectional drive ratchet head, our torque wrench can be measured both clockwise and counterclockwise. When the set torque value is reached, a "click" sound will remind you to stop applying force to prevent damage to the item due to excessive torque. Notice: At low Nm settings under 5 Nm the "click" sound can be too light to hear.
Bestseller No. 9
etoolab 1/2 Drive Click Torque Wrench Dual-Range【10-170.0ft.lb/10-227Nm】±3% Precision Torque Wrench 1/2 Drive, 72 Tooth Dual-Direction Adjustable Torque Wrench for Bicycle, Moto and Car Maintenance
  • 🔧【𝐌𝐢𝐥𝐢𝐭𝐚𝐫𝐲-𝐠𝐫𝐚𝐝𝐞 𝐒𝐭𝐞𝐞𝐥】ETOOLAB torque wrench utilizes military-grade steel as its base material, coupled with professional surface rust protection methods tailored to usage habits. While ensuring user comfort, it enhances product strength, wear resistance, and rust resistance. offers a more comfortable experience and a longer lifespan!
  • 👍【𝐄𝐚𝐬𝐲-𝐭𝐨-𝐑𝐞𝐚𝐝】The scale of this 1/2 drive torque wrench is laser-engraved, using a black background with white markings. dinamometrica de 1/2 ensures clear and easy readability of the scale, even in sunlight. With a dual-scale design, users can conveniently read torque values in two different units according to their preferences, without the need for conversion!
  • ⚙️【±𝟑% 𝐏𝐫𝐞𝐜𝐢𝐬𝐢𝐨𝐧 & 𝐒𝐢𝐦𝐩𝐥𝐞 𝐋𝐨𝐜𝐤𝐢𝐧𝐠 𝐑𝐢𝐧𝐠】Our torque wrench 1/2 drive meets the high precision standard of ±3% and comes with a traceable serial certificate. You can use it with confidence! Moreover, its graduation ring is tightly locked, with smaller incremental values, ensuring precise and consistent torque output even after multiple uses. This reduces the hassle of frequent adjustments. It is undoubtedly an excellent tool for your work!
  • 🔊【𝐋𝐨𝐮𝐝 𝐂𝐥𝐢𝐜𝐤 𝐒𝐨𝐮𝐧𝐝】This torque wrenches has been upgraded to have a louder "Click" sound. We conducted over 25,000 tests to ensure that each product produces a click sound volume of no less than 45dB when the torque value exceeds 34 lbf·ft. When you hear the distinct click sound, it indicates that the preset torque has been reached, signaling you to stop applying force. You no longer need to worry about damaging your mechanical components.
  • 💯【𝐔𝐬𝐞𝐫-𝐅𝐫𝐢𝐞𝐧𝐝𝐥𝐲】Our torque wrench set features a 72-tooth dual-directional ratchet head, allowing for easy operation in both clockwise and counterclockwise directions. It is designed with an adjustable locking ring, making it effortless to adjust the preset torque value. Additionally, it includes a quick-release head design, allowing it to replace the wrench head accessories more easily!
Bestseller No. 10
TEKTON 1/4, 3/8, 1/2 Inch Drive Micrometer Torque Wrench Set (3-Piece) | TRQ99901
  • Includes 1-pc. 1/4 in. drive micrometer torque wrench (20-200 in.-lb.) with storage case and product manual; 1-pc. 3/8 in. drive micrometer torque wrench (10-80 ft.-lb.) with storage case and product manual; 1-pc. 1/2 in. drive micrometer torque wrench (25-250 ft.-lb.) with storage case and product manual
  • Wrenches emit a click that can be heard and felt when the preset value is reached
  • Permanently marked, high-contrast dual-range scale is easy to read, even in low light
  • Reversible ratchet heads drive in both directions and measure torque in clockwise direction
  • Durable all-steel construction has no plastic parts to break or wear out

Last update on 2024-03-28 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...