M.I.L. ON with DTC P0300 (Random Misfire) and/or P030# (Single Cylinder Misfire) – 2003-2004 Toyota Celica

EG031-04
August 11, 2004

 

Title:

M.I.L. ON DTC P0300 (RANDOM MISFIRE) AND/OR P030# (SINGLE CYLINDER MISFIRE)

 

Models: 03 – 04 Celica (1ZZ-FE, Manual Transmission)

IntroductionUnder certain conditions, some 2003 – 2004 model year Celica vehicles may exhibit M.I.L. ON with DTC P0300 (Random Misfire) and/or P030# (Single Cylinder Misfire).

The Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) logic has been modified to correct this condition.

Applicable Vehicles
  • 2003 – 2004 model year Celica vehicles equipped with 1ZZ-FE engine and manual transmission produced BEFORE the Production Change Effective VIN shown below.

 

Production Change Information

MODELENGINETRANSMISSIONPRODUCTION CHANGE EFFECTIVE VIN
Celica1ZZ–FEManualJTDDR3#T#40176236

 

 

Parts Information

PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAMEQTY
89661-2G38189661-2G382Computer, Engine Control1

 

Required SSTs

SPECIAL SERVICE TOOLS (SSTs)PART NUMBERQUANTITY
ToyotaeBay logo Diagnostic Tester Kit*010012711
12 Megabyte Diagnostic Tester Program Card with version 10.2a Software (or later)*01002593-0051

 

*Essential SSTs.

 

NOTE:

Additional Diagnostic Tester Kits, Program Cards or other SSTs may be ordered by calling SPX/OTC at 1-800-933-8335.

 

Warranty Information

OP CODEDESCRIPTIONTIMEOFPT1T2
EG4012Connection of Diagnostic Tester and

R & R Engine ECM (PCM)

0.989661-2G3818A74

 

Applicable Warranty*:

This repair is covered under the ToyotaeBay logo Specified Major Emission Control Component Warranty. This warranty is in effect for 96 months or 80,000 miles, whichever occurs first, from the vehicle s in-service date.

*Warranty application is limited to correction of a problem based upon a customer s specific complaint.

 

Repair Procedure

  1. Should a M.I.L. ON condition with DTC P0300 and/or P030# be encountered, perform diagnostic procedures as described in the Technical Information System (TIS) 2003 or 2004 model year Celica Repair Manual: Diagnostics: Engine (1ZZ-FE): P0300, P0301, P0302, P0303, P0304 Cylinder 4 Misfire Detected (Celica).
  2. If the problem source cannot be identified after checking all affected areas according to TIS, the cause may be an ECM (PCM) logic malfunction. In this case, replace the ECM (PCM) with the updated part according to TIS:
    • 2003 model year Celica Repair Manual: Engine Mechanical: Engine Unit: Removal (steps 10 a-d).
    • 2004 model year Celica Repair Manual: Engine Mechanical: Engine Unit: Removal (steps 12 a-d).
ECM

 

 

 


J2534 Reprogramming

Approved J2534 Devices only provide reprogramming capabilities and do not support diagnostic scantool functions. For full diagnostic capabilities, please consider TIS Techstream or Techstream Lite

ToyotaeBay logo, ScioneBay logo, and Lexus ECMs can be reprogrammed with the TIS Techstream, Techstream Lite, Diagnostic Tester, or can also be reprogrammed using a ToyotaeBay logo validated J2534 interface. Vehicle recalibration requires the use of the following:

  • ToyotaeBay logo validated J2534 interface
  • TIS Professional Level Subscription
  • ToyotaeBay logo Calibration Update Wizard software (installed along with Techstream Software)
  • Personal Computer running Microsoft Windows XP/2000 or later operating system

ToyotaeBay logo strongly recommends USING ONLY VALIDATED INTERFACE DEVICES that appear on this list.

ToyotaeBay logo works closely with J2534 interface manufacturers to ensure that their hardware works safely and efficiently with our products. Every device listed on this page has been thoroughly tested and validated on ToyotaeBay logo, ScioneBay logo, and Lexus vehicles.

It is important to understand that only the specific devices, firmware, DLLs and APIs listed here have been tested by ToyotaeBay logo. We do not recommend use of any other J2534 device, firmware, DLL or API that is not listed here. Changes to J2534 hardware/software is outside of ToyotaeBay logo’s control; in some cases, changes made to device hardware/software can negatively impact reprogramming performance. ToyotaeBay logo makes every effort to continue to work with J2534 interface manufacturers to ensure continued product compatibility as our respective products evolve.

 

J2534 Approved Device Application Chart

SupplierDevice NameVersionCUW VersionSupported OS
Firmware*DLL*API*
Bosch DiagnosticsFlasher LT-Import01.02.0701.02.0704.048.8B, C, D, E
Bosch DiagnosticsFlasher PRO01.09.1801.09.1804.048.8B, C, D, E
Bosch DiagnosticsMastertech VCI13.0.75.272.0.75.2704.04Testing in ProgressB, C, D, E
Dearborn GroupVSI-25341.1122.05.2204.048.10C, D
Drew TechnologiesCarDAQ Plus

No products found.

01.09.1801.09.1804.048.8B, C, D, E
Drew TechnologiesMongoose MFC

No products found.

01.02.0701.02.0704.048.8B, C, D, E
Drew TechnologiesMongoose PRO

No products found.

1.1.12.01.1.12.004.048.16A, B, C, D
Snap-OnPass Thru Pro II01.09.1801.09.1804.048.8B, C, D, E

 

*Original validated firmware/DLL versions may be superceded by the device manufacturer. Contact the device manufacturer if you are unable to find the versions listed above.

 

Supported Operating Systems

AWindows 8 (32-bit; 64-bit)
BWindows 7 (32-bit; 64-bit)
CWindows VISTA Home Basic, Home Premium, Business, Ultimate
DWindows XP Pro SP1 or later
EWindows 2000 SP2 or later

 

For more information about the J2534 devices listed above, click on the vendor names. To report compatibility problems with listed hardware/software, please contact the device manufacturer.

 

Obtaining Calibration Files

The Flash Reprogramming Calibration CD is no longer available.

ECU Calibrations are now available for download directly from TIS. A valid TIS Professional Level subscription is required to access Calibration files. These files are compatible with the above mentioned scantools and J2534 interfaces. The Calibration page, located on the Diagnostics tab in the TIS site, contains all the most current vehicle calibration files, applicable Service Bulletins, and instructions for use. Select the following link for step by step instructions to access this page.

Note: Calibration Update Software is now included in the Techstream Software Installer. A valid TIS Professional Level subscription is required to download and install Techstream Software.

 

 

 

Clore Automotive Jump-N-Carry JNC660 1700 Peak Amp 12 Volt Jump Starter , Blue
  • 22Ah Clore Proformer Battery designed for Jump Starting
  • 46" Heavy-Duty #2 AWG Cables
  • Voltmeter provides charge status of on board battery
  • 1700 Peak Amps
  • DC outlet to power 12V accessories

Last update on 2026-06-17 / Affiliate links / Images from Amazon Product Advertising API


 

No products found.

No products found.

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...