SAFETY RECALL JLI/JLJ/JLK – Front Passenger Airbag Module – 2010-2017 Lexus GX460

SEOCONTENT-START

IMPORTANT UPDATE
TECHNICAL INSTRUCTIONS
FOR
SAFETY RECALL JLI/JLJ/JLK
FRONT PASSENGER AIRBAG MODULE
CERTAIN 2010-2017 MY GX 460
The repair quality of covered vehicles is extremely important to Lexus. All dealership technicians performing this recall are required to successfully complete the most current version of the E-Learning course “Safety Recall and Service Campaign Essentials”. To ensure that all vehicles have the repair performed correctly:
• MASTER SERVICE TECHNICIANS
• MASTER DIAGNOSTIC SPECIALISTS
It is the dealership’s responsibility to select technicians with the above certification level or greater to perform this recall repair. Carefully review your resources, the technician skill level, and ability before assigning technicians to this repair. It is important to consider technician days off and vacation schedules to ensure there are properly trained technicians available to perform this repair at all times.
NOTE: To support additional service capacity, Lexus Certified and Senior Service Technicians, with at least 36 months Lexus experience AND L652 course credit, may also perform this repair following successful completion of course LSC13B.
2
I. OPERATION FLOW CHART
The flow chart is for reference only. DO NOT use it in place of the full technical instructions. Follow ALL steps as outlined in the full technical instructions to confirm the campaign is completed correctly.
Verify Vehicle Eligibility1. Check the TIS Vehicle Inquiry System.No further action required.Not CoveredCampaign complete, return the vehicle to the customer.CoveredReplace the module.Reinstall the dash pad.Record the airbag serial number as instructed in the TIRemove the dash pad and remove the airbag module.
II. BACKGROUND
The subject vehicles are equipped with front passenger airbag inflators produced by Takata. The propellant in these inflators may degrade after prolonged exposure to high absolute humidity and fluctuating high temperatures. Degraded propellant can cause inflator rupture during airbag deployment. In the event of an inflator rupture, metal fragments could pass through the airbag cushion material, striking the vehicle occupants, and result in serious injury or death.
3
III. IDENTIFICATION OF AFFECTED VEHICLES
A. COVERED VIN RANGE
• Check the TIS Vehicle Inquiry System to confirm the VIN is involved in this Safety Recall, and that the campaign has not already been completed prior to dealer shipment or by another dealer.
• TMS warranty will not reimburse dealers for repairs conducted on vehicles that are not affected or were completed by another dealer.
IV. PREPARATION
A. PARTS
Part Number
Part Description
Quantity
04007-58160
Instrument Panel Passenger Airbag
1
Non-Desiccated Part Recovery
Dealers should discontinue the installation of the non-desiccated parts listed below for recall, customer pay repairs AND over-the-counter sales (if applicable).
Model
Model Year
Part Number
Part Description
GX460
2010-2017
73960-60250
AIR BAG ASSY,
INSTR PNL PASS L/DOOR
Lexus requires all dealers to return any parts listed above that still remain in dealer inventory by utilizing the Hazmat Part Return Program available. Dealers will be issued a refund for all part returns. This part return program is outlined in PANT Bulletin 2014-042.
Important Note:
In order to return the inflator, packages must NOT be opened/tampered with.
4
B. TOOLS & EQUIPMENT
• Standard hand tools
• Torque wrench
• Techstream
• Molding remover set
GLG/GLH CAMPAIGN TOOLS – These tools are required when performing this repair.
Image
Name
Quantity
Barcode Scanner
(The scanner was previously proved for SSC DLC)
1
NOTE: This scanner CANNOT be ordered through the parts or tools system. If additional tools are needed, they can be sourced locally.
SST –These are essential service tools that the dealership should have.
Part Number
Part Name
Quantity
09950-50013
Puller C Set *
1
* The set above includes the following tools.
Part Number
Part Name
Quantity
09951-05010
Hanger 150
1
09952-05010
Slide Arm
2
09953-05020
Center Bolt 150
1
09954-05021
Claw No. 2
2
5
V. SAFETY PRECAUTIONS
CRITICAL INFORMATION – READ THOROUGHLY
Failure to follow these procedures correctly could cause the SRS to unexpectedly deploy during servicing or the SRS may fail to operate correctly when required after reassembly. Confirm all work is performed as described in these instructions.
1. ELIMINATE STATIC ELECTRICITY
a) Before starting work and periodically while working on the vehicle, touch a metallic part of the vehicle to discharge static electricity in the body.
2. DO NOT MEASURE RESISTANCE
a) NEVER measure the resistance of an airbag, this may cause accidental activation.
3. HANDLE THE AIRBAG CAREFULLY
a) If the airbag is dropped, replace it with a NEW one.
4. WEAR PROTECTIVE EQUIPMENT
a) Always wear appropriate protective equipment when working on the SRS.
6
VI. SRS SYSTEM HEALTH CHECK
1. PERFORM A HEALTH CHECK
a) Confirm the Techstream is connected to the dealership’s internet.
b) When launching the Techstream software the VIN may auto populate if not then it MUST be entered manually.
NOTE: All letters of the VIN MUST be entered in ALL CAPS, or the VIN will need to be reentered when running the diagnostic report.
c) Perform a health check.
Note: The VIN may auto populate on the later model year vehicles, if this happens DO NOT change the VIN.
2. RUN A DIAGNOSTIC REPORT
a) After the health check has completed, run a diagnostic report by clicking on the link on the health check screen.
NOTE: If the VIN was not entered in ALL CAPS when Techstream was launched, an error will be displayed and there will be a prompt to reenter the VIN
b) Enter the vehicle mileage and repair order information, then click the ‘report’ button.
• A health check and diagnostic report with the VIN MUST be performed within the last 36 hours, and recorded by TMNA. If the diagnostic report is not run, the healthcheck will not be recognized by TMNA.
• The serial number recording application will be disabled and the repair cannot be completed if a health check and diagnostic report is not performed and recorded by TMNA.
• This campaign only covers replacement of the passenger dash airbag. If other SRS repairs are needed they are NOT covered under this campaign.
7
VII. FRONT PASSENGER AIRBAG REMOVAL
COMPONENTS
8
9
10
11
1. REMOVE THE AIRBAG MODULE
• Wait at least 90 seconds after disconnecting the cable from the negative battery terminal to prevent airbag and seat belt pre-tensioner deployment.
• Follow all precautions as outlined on TIS before servicing the SRS system.
a) Refer to TIS for removal instructions.
NOTE: For vehicles equipped with a cool box DO NOT DISCONNECT THE REFRIGERANT HOSES refer to the APPENDIX for information about removing and installing the center console.
2010 MY
2011 MY
2012 MY
2013 MY
2014 MY
2015 MY
2016 MY
2017 MY
12
VIII. AIRBAG RECORDING
1. LAUNCH THE SERIAL NUMBER RECORDING APPLICATION
Note: The Serial Number Recording Application is the same application used for a prior campaign.
• The AIRBAG ASSEMBLY serial numbers MUST be recorded using a barcode scanner (provided at the launch of SSC DLC).
• The barcode scanner application MUST be completed on every vehicle. These numbers MUST be included on every warranty claim that is submitted for airbag module replacement or the claim may be subject to debit.
• The technician performing the work MUST have valid TIS login credentials and an internet connection to perform the inspection and scanning process.
a) Log in to TIS and input the VIN of the vehicle in the Vehicle Inquiry tab.
b) Confirm the VIN is applicable and that the campaign has not been completed.
c) Click on the link to launch the serial number recording application.
d) Reenter TIS password in the serial number recording application.
NOTE: The person logged-in to TIS MUST be the person performing the repair.
e) Record the vehicle mileage into the serial number recording application.
NOTE:
• A task status screen will populate next and at other intervals during the repair. This screen will indicate if the airbag was replaced. Click ‘next’ to proceed to the next step. This information will be used for record keeping by TMNA.
• If this screen indicates that the campaign has already been completed on this VIN, there is no need to perform the campaign again.
13
2. CONNECT THE BARCODE SCANNER
a) Connect the barcode scanner to the USB port on the Techstream.
b) The scanner will automatically connect and a beep will be heard when the scanner is ready.
NOTE:
• The scanner was provided for SSC DLC.
• The barcode scanner works best in low light conditions.
• Always hold the scanner directly in front of and parallel to the barcode label.
3. SCAN THE AIRBAG SERIAL NUMBER
ATTENTION: This information is CRITICAL
a) Scan the AIRBAG ASSEMBLY serial number 2 times.
1) Confirm that the cursor is in the first serial number box and scan the bar code.
2) Position the cursor in the second serial number box and rescan the bar code.
b) Click next.
NOTE:
• If the serial numbers do not match, confirm and reenter.
• If the serial number barcode will not scan, it can be entered manually.
AIRBAG SERIAL NUMBER IDENTIFICATION
• The airbag serial number is ALWAYS the 12 DIGITS located between the asterisks.
• The 3 digits before the asterisk ARE NOT part of the serial number, and SHOULD NOT be entered or an inaccurate response may be returned.
Airbag Serial Number Label Example
The AIRBAG ASSEMBLY serial number MUST be recorded prior to replacement.
SSC DSC
14
c) Check the box that states that the inflator serial number is not visible or missing.
(DO NOT SCAN THE INFLATORS)
(this will allow the program to advance to the next screen)
d) Confirm agreement by checking the two boxes and press submit.
NOTE: The NEW AIRBAG ASSEMBLY serial number MUST be scanned prior to reinstallation to track the airbag to the vehicle (refer to page 14).
15
e) Scan the NEW Airbag barcode in the Serial Number Recording Application.
f) Confirm agreement by checking the two boxes and press next.
The new AIRBAG ASSEMBLY serial number MUST be recorded prior to reinstallation to track the airbag to the vehicle.
SSC DSC
16
g) Record the Warranty Authorization # to be included in the warranty claim.
h) Confirm agreement by checking the two boxes.
i) Place the old airbag in the parts box and return it to the parts department.
NOTE:
• Keep all shipping paperwork with the box that it came in.
• Confirm the cursor is in the correct serial number input box before scanning.
• If the serial number barcode will not scan, it can be entered manually.
• If there are any difficulties or concerns with this process, email quality_compliance@toyota.com with details.
17
AIRBAG SERIAL NUMBER IS MISSING OR IS UNREADABLE
If the airbag serial number and barcode are not legible or are not present, check the box in the application indicating the serial number is not legible.
a) If the airbag serial number cannot be scanned or is not present check the box as shown below.
Check this box if the label is damaged or missing
b) Return to Page 13 and continue.
SSC DSC
18
IX. VEHICLE REASSEMBLY
1. INSTALL THE NEW AIRBAG ASSEMBLY INTO THE INSTRUMENT PANEL
2. REINSTALL THE DASH
a) Refer to TIS for reinstallation instructions
2010 MY
2011 MY
2012 MY
2013 MY
2014 MY
2015 MY
2016 MY
2017 MY
NOTE: Refer to the APPENDIX to reinstall the center console for vehicles equipped with a cool box.
3. RECONNECT THE NEGATIVE BATTERY CABLE
4. PERFORM A HEALTH CHECK AND DIAGNOSTIC REPORT
5. PERFORM ANY NEEDED SYSTEM INTIALZATIONS
◄ VERIFY REPAIR QUALITY ►
− Confirm all precautions are followed to ensure safety during the repair
− Confirm the entire serial number checker application is completed and the warranty authorization # is recorded on EVERY vehicle
− Confirm the old airbag is handled safely and given to the appropriate parts professional for shipment
If you have any questions regarding this update, please contact your area representative.
X. APPENDIX
A. COOL BOX TRIM REMOVAL AND INSTALLATION
NOTE: The trim around the cool box can be removed and installed without disconnecting the refrigerant lines.
19
1. REMOVE THE CONSOLE BOX
a) Remove the 2 bolts and 2 screws.
b) Disengage the clamp.
c) Remove the 6 screws.
d) Remove the console door.
e) Remove the 6 screws.
20
f) Disengage the 6 claws on each side of the console as shown.
NOTE: DO NOT DAMAGE the surrounding interior components while removing the console box.
g) Pull the console box towards the rear of the vehicle, then lift the rear of the box as shown, and remove from vehicle.
21
2. REINSTALL THE CONSOLE BOX
a) Install the front of the console box with rear section lifted as shown.
b) Lower the rear of the box and then slide it forward.
22
c) Reengage the 6 claws on each side of the console as shown.
d) Reinstall the 6 screws.
e) Reinstall the console door.
f) Reinstall the 6 screws
23
g) Reengage the clamp.
h) Reinstall the 2 bolts and 2 screws.
B. CAMPAIGN DESIGNATION DECODER
E0AYear Campaign is LaunchedA = 2010B = 2011C = 2012 D = 2013E = 2014F = 2015G = 2016Etc…Repair Phase1st Campaign = A2nd Campaign = B3rd Campaign = C4th Campaign = D5th Campaign = E27th Campaign = 128th Campaign = 2Etc…Current Campaign Letter for this year 0 = Remedy1 = Interim (Remedy not yet available) “1” will change to “0” when the Remedy is available(May use other characters in unique cases)
Examples:
A0D = Launched in 2010, Remedy Phase, 4th Campaign Launched in 2010
B1E = Launched in 2011, Interim Phase, 5th Campaign Launched in 2011
C1C = Launched in 2012, Interim Phase, 3rd Campaign Launched in 2012
C. CAMPAIGN PARTS DISPOSAL
ALL airbags that are removed from vehicles under this campaign MUST be packaged and shipped back to the manufacturer following the manufacturer’s instructions. The instructions can be found in the following locations:
• Attached to the dealer letter
• Included in the parts box

SEOCONTENT-END