24LA02 – Vehicle May Move While In Neutral Position – 2022-2024 Lexus LX600

“This site contains affiliate links for which OEMDTC may be compensated”

February 21, 2024 NHTSA CAMPAIGN NUMBER: 24V125000

Unexpected Vehicle Movement

Unexpected vehicle movement can increase the risk of a crash.

 

NHTSA Campaign Number: 24V125

Manufacturer ToyotaeBay Motor Engineering & Manufacturing

Components POWER TRAIN

Potential Number of Units Affected 280,663

 

Summary

ToyotaeBay Motor Engineering & Manufacturing (ToyotaeBay) is recalling certain 2022-2024 Tundra, Tundra Hybrid, Lexus LX600, and 2023-2024 Sequoia Hybrid vehicles. Unexpected vehicle movement may occur when the vehicle is in neutral and the brakes are not applied.

 

Remedy

Dealers will update the transmission control ECU software, free of charge. Owner notification letters are expected to be mailed April 7, 2024. Owners may contact ToyotaeBay customer service at 1-800-331-4331. ToyotaeBay’s numbers for this recall are 24TA02 and 24LA02.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.

 

Check if your Vehicle has a Recall

 


SAFETY RECALL 24LA02 (Remedy Notice)
Certain 2022 – 2024 model year LX600
Vehicle May Move While In Neutral Position

On February 21st, 2024, Lexus filled a Defect Information Report (DIR) with the National Highway Traffic Safety Administration (NHTSA) informing the agency of our intent to conduct a voluntary Safety Recall on 2022-2024 model year LX600 vehicles.

 

Condition 

Certain parts of the transmission may not immediately disengage when the vehicle is shifted to the neutral position.  This can allow some engine power to continue to be transferred to the wheels and can allow the vehicle to inadvertently creep forward at a low speed when it is on a flat surface and no brakes are applied, leading to an increased risk of a crash.

 

Remedy

Lexus dealers will update the software for the transmission control computer FREE OF CHARGE.

 

Covered Vehicles

There are approximately 12,100 vehicles covered by this Safety Recall. Approximately 100 vehicles involved in this Safety Recall were distributed to Puerto Rico

 

Owner Letter Mailing Date

Lexus will notify owners by late April 2024.

 


Description of Problem:

The transmission assembly in the subject vehicles uses a clutch piston to engage brake clutch discs to plates to transfer power from the engine to the wheels. There is a possibility that, due to an issue in the design of a certain brake clutch disc, when the transmission is shifted to the neutral position and pressure is removed from the clutch piston, the brake clutch discs will not immediately disengage from the plates, allowing some engine power to continue to transfer to the wheels. If this condition occurs when the vehicle is on a flat surface, and if the driver does not apply the service brake or the parking brake, it could allow a vehicle to inadvertently creep forward at a low speed (up to approximately 4 mph), which could increase the risk of a crash.

 

Chronology of Principal Events:

May 2023 – October 2023
In late May, ToyotaeBay received a field report alleging that a customer’s vehicle moved forward while the transmission was placed in neutral. An initial inspection was conducted by the dealer, during which the transmission was moved to neutral, the brake pedal was released, and the vehicle was observed to move forward under its own power on a flat surface. The dealer observed a top vehicle speed of 3 mph during this movement in neutral.

ToyotaeBay conducted an additional vehicle inspection to further evaluate the customer’s vehicle. ToyotaeBay completed a test drive and collected vehicle data (e.g., distance, speed, force, etc.) that confirmed that the vehicle would begin slowly moving from a stop to approximately 3 mph while in the neutral shift position with no brakes applied. ToyotaeBay also confirmed that the service brakes and parking brakes were not impacted by the condition, and if the driver applied either of the brakes, the vehicle would stop moving.

In late June, ToyotaeBay began further testing to determine the actual torque being transmitted from the engine to the wheels during this neutral range movement. Simultaneously, ToyotaeBay performed testing on additional vehicles in order to quantify the actual rolling resistance torque which was found to be smaller than the torque being transferred from the engine to the wheels. The difference in the two torques was small but determined to be enough for limited movement to occur.

Following determination of the actual torque conditions, ToyotaeBay continued with the recovery and evaluation of parts from two vehicles with newly submitted field reports. Once the presence of neutral movement on the vehicles with the recovered parts was confirmed, ToyotaeBay performed bench testing on the recovered parts to identify how torque was being transferred from the engine to the wheels. During this bench testing, it was found that certain brake clutch discs were not immediately separating from plates after the transmission was shifted into the neutral position and some power could continue to be transferred from the engine to the wheels. The occurrences were intermittent, and it appeared that the brake clutch discs were overly flat, which could contribute to the delay in disc separation.

ToyotaeBay then made a change in the design of the brake clutch disc in order to change the level of flatness, however the verification testing of the design change failed.

November 2023 – February 2024
In early November, because the design change for disc flatness had failed, ToyotaeBay continued investigating the brake clutch disc mechanism. As a result of this investigation, a software change in the transmission control ECU was introduced at the manufacturing facility.

Following successful verification of transmission control ECU software changes, ToyotaeBay developed a testing plan to understand the customer usage scenarios along with any potential risks associated with those scenarios involving the condition. Before the testing plan was completed, ToyotaeBay received a field report that alleged movement of a vehicle in the neutral position while passing through a car wash.

February 15, 2024
Based on the results of the above investigation, ToyotaeBay decided to conduct a voluntary safety recall campaign.
As of February 13, 2024, based on a diligent review of records, ToyotaeBay’s best engineering judgment is that there are 5 ToyotaeBay Field Technical Reports and 1 warranty claim that have been received from U.S. sources that relate or may relate to this condition and which were considered in the decision to submit this report.

 

Description of Corrective Repair Action:

All known owners of the subject vehicles will be notified to return their vehicles to a ToyotaeBay or Lexus dealer. The dealers will update the software of the transmission control ECU, free of charge.

 


Vehicle May Move While Neutral In Motion – 2022-2024 Lexus LX600

 

 


11 Affected Products

Vehicles

MAKEMODELYEAR
LEXUSLX2022-2024
TOYOTAeBaySEQUOIA HYBRID2023-2024
TOYOTAeBayTUNDRA2022-2024
TOYOTAeBayTUNDRA HYBRID2022-2024

 


14 Associated Documents

Recall Acknowledgement

RCAK-24V125-9649.pdf 645.416KB

 


Remedy Instructions and TSB

RCRIT-24V125-8299.pdf 624.502KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [609.87 KB]

 


Manufacturer Notices(to Dealers,etc) – Date: February 21st, 2024 SAFETY RECALL 24LA02 (Remedy Notice)

RCMN-24V125-1365.pdf 452.33KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [441.73 KB]

 


Manufacturer Notices(to Dealers,etc)

RCMN-24V125-0881.pdf 66.422KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [64.87 KB]

 


Manufacturer Notices(to Dealers,etc)

RCMN-24V125-2360.pdf 83.416KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [81.46 KB]

 


Manufacturer Notices(to Dealers,etc) – Lexus Date: February 21st, 2024 Specific information for Area support

RCMN-24V125-9075.pdf 59.646KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [58.25 KB]

 


Remedy Instructions and TSB – TECHNICAL INSTRUCTIONS FOR 24TA02

RCRIT-24V125-3638.pdf 853.719KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [833.71 KB]

 


Remedy Instructions and TSB – TECHNICAL INSTRUCTIONS FOR 24LA02

RCRIT-24V125-5005.pdf 564.954KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [551.71 KB]

 


Manufacturer Notices(to Dealers,etc) – Date: February 21st, 2024 SAFETY RECALL 24TA02 (Remedy Notice)

RCMN-24V125-9902.pdf 495.364KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [483.75 KB]

 


Manufacturer Notices(to Dealers,etc) – ToyotaeBay Date: February 21st, 2024 Specific information for Region support

RCMN-24V125-4790.pdf 53.411KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [52.16 KB]

 


February 21, 2024 DEFECT INFORMATION REPORT

RMISC-24V125-1333.pdf 30.294KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [29.58 KB]

 


Defect Notice 573 Report

RCLRPT-24V125-8877.PDF 218.229KB

 


Remedy Instructions and TSB

RCRIT-24V125-1220.pdf 680.025KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [664.09 KB]

 


Remedy Instructions and TSB

RCRIT-24V125-2237.pdf 657.138KB

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [641.74 KB]

 


Latest Recalls Documents

For the Latest and Most recent Recall Information Visit the link below…

 


 

Reprogramming

J2534 Reprogramming

Approved J2534 Devices only provide reprogramming capabilities and do not support diagnostic scantool functions. For full diagnostic capabilities, please consider TIS Techstream or Techstream Lite

ToyotaeBay, ScioneBay, and Lexus ECMs can be reprogrammed with the TIS Techstream, Techstream Lite, Diagnostic Tester, or can also be reprogrammed using a ToyotaeBay validated J2534 interface. Vehicle recalibration requires the use of the following:

  • TIS Professional Level Subscription
  • Personal Computer running Microsoft Windows XP/2000 or later operating system

ToyotaeBay strongly recommends USING ONLY VALIDATED INTERFACE DEVICES that appear on this list.

ToyotaeBay works closely with J2534 interface manufacturers to ensure that their hardware works safely and efficiently with our products. Every device listed on this page has been thoroughly tested and validated on ToyotaeBay, ScioneBay, and Lexus vehicles.

It is important to understand that only the specific devices, firmware, DLLs and APIs listed here have been tested by ToyotaeBay. We do not recommend use of any other J2534 device, firmware, DLL or API that is not listed here. Changes to J2534 hardware/software is outside of ToyotaeBay's control; in some cases, changes made to device hardware/software can negatively impact reprogramming performance. ToyotaeBay makes every effort to continue to work with J2534 interface manufacturers to ensure continued product compatibility as our respective products evolve.

 

J2534 Approved Device Application Chart

Device
Name
Supplier Version CUW
Version
Supported OS
Firmware* DLL* API*
Flasher LT-Import Bosch Diagnostics 01.02.07 01.02.07 04.04 8.8 B, C, D, E
Flasher PRO Bosch Diagnostics 01.09.18 01.09.18 04.04 8.8 B, C, D, E
Mastertech VCI Bosch Diagnostics 13.0.75.27 2.0.75.27 04.04 Testing in Progress B, C, D, E

VSI-2534

Dearborn Group 1.112 2.05.22 04.04 8.10 C, D

CarDAQ Plus

24LA02 - Vehicle May Move While In Neutral Position - 2022-2024 Lexus LX600 | small light

Drew Technologies 01.09.18 01.09.18 04.04 8.8 B, C, D, E
Mongoose MFC Drew Technologies 01.02.07 01.02.07 04.04 8.8 B, C, D, E

Mongoose PRO

Drew Technologies 1.1.12.0 1.1.12.0 04.04 8.16 A, B, C, D
Pass Thru Pro II Snap-On 01.09.18 01.09.18 04.04 8.8 B, C, D, E

*Original validated firmware/DLL versions may be superceded by the device manufacturer. Contact the device manufacturer if you are unable to find the versions listed above.

 

Supported Operating Systems

A Windows 8 (32-bit; 64-bit)
B Windows 7 (32-bit; 64-bit)
C Windows VISTA Home Basic, Home Premium, Business, Ultimate
D Windows XP Pro SP1 or later
E Windows 2000 SP2 or later

For more information about the J2534 devices listed above, click on the vendor names. To report compatibility problems with listed hardware/software, please contact the device manufacturer.

 

CarDAQ-Plus 2 Diagnostic Code Reader and J2534 Programming Tool
24LA02 - Vehicle May Move While In Neutral Position - 2022-2024 Lexus LX600 | small light Drew Technologies (DRWCDPLUSKIT) CarDAQ-Plus J2534 Flash Reprogramming Kit
24LA02 - Vehicle May Move While In Neutral Position - 2022-2024 Lexus LX600 | small light CarDAQ-M Modular PassThru J2534 Vehicle Reflash Hardware
24LA02 - Vehicle May Move While In Neutral Position - 2022-2024 Lexus LX600 | small light VSI J2534 ECU Reprogrammer & Diagnostic Adapter
Dearborn d-Bridge Adapter J2534 OBDII Engineering Tool
24LA02 - Vehicle May Move While In Neutral Position - 2022-2024 Lexus LX600 | small light MAXIFLASH PRO (ALT-MF2534)

 


Obtaining Calibration Files

The Flash Reprogramming Calibration CD is no longer available.

ECU Calibrations are now available for download directly from TIS. A valid TIS Professional Level subscription is required to access Calibration files. These files are compatible with the above mentioned scantools and J2534 interfaces. The Calibration page, located on the Diagnostics tab in the TIS site, contains all the most current vehicle calibration files, applicable Service Bulletins, and instructions for use. Select the following link for step by step instructions to access this page.

Note: Calibration Update Software is now included in the Techstream Software Installer. A valid TIS Professional Level subscription is required to download and install Techstream Software.

 

https://techinfo.toyota.com

 


 

Bestseller No. 1
TOPDON RLink J2534 Pass-Thru Programmer, OEM Reprogramming and Diagnostic Tool, Enhanced J2534 VCI, Supports J2534/D-PDU/CAN-FD/DoIP, Compatible with 17+ Vehicle Brands, No OE Software Provided
  • J2534 Pass-Thru Programmer: TOPDON RLink J2534 is an advanced diagnostic and reprogramming tool that support all J2534 protocols, as well as D-PDU, CAN-FD and DoIP, ensuring compatibility with a wide range of modern vehicles. It offers extensive versatility with support for over 17 major automotive brands, including Chrysler, Ford, GM, Nissan, ToyotaeBay, HondaeBay, Subaru, Land Rover/Jaguar, Volvo, Wuling, VolkswageneBay, Mercedes-Benz, and BMWeBay, and so on, enjoy dealership-level functions at your fingertips
  • All-in-One OEM Diagnostics: This J2534 ECU programming tool elevates your automotive repair capabilities to new heights by delivering complete OEM diagnosis. Boasting comprehensive full-system diagnostics, intuitive repair guides, advanced ECU programming and coding, common reset services, a vast library of repair information and more, this all-in-one solution empowers technicians to effortlessly tackle complex vehicle issues with ease
  • Proven Performance You Can Trust: Backed by over 10000 real vehicle tests and benefit from a wealth of practical experience, this OEM reprogramming tool guarantees stable and exceptional performance. Supported by TOPDON's dedicated technical experts with in-depth knowledge of both auto repair and J2534 Pass-Thru programming, the RLink J2534 provides prompt and professional assistance, ensuring a smooth setup and reliable compatibility
  • Integrated Excellence, Always Up-to-Date: Featuring the exclusive RLink Platform to provide a streamlined experience with one-click driver installation and management, ensuring flawless integration with your OE software, maintaining the original performance quality. The built-in operation guide makes mastering OE software quick and easy, so you can get started right away. Plus, with lifetime free updates, your diagnostics will stay current with the latest drivers and innovations
  • Efficiency Meets Versatility: Engineered to support three CAN channels simultaneously - CAN FD and CAN-CC included, giving you the edge in fast troubleshooting. To perfectly synchronized with the OE software, please diagnose with active subscriptions and make sure your computer system is running a compatible 64-bit Windows version (7, 8, 10 or later) to fully leverage the power of RLink J2534. *We don't provide extra OE software
Bestseller No. 2
LAUNCH X431 PRO3S+ Elite, 2025 All-in-One Bidirectional Scan Tool with J2534,HD Trucks Scan, Topology Map, 60+Service,Online Coding Full Function Scanner, CANFD/DoIP/D-PDU/CAN 2.0, FCA, 2 Yrs Update
  • J2534 PROTOCOL WITH SMARTLINKC】 LAUNCH X431 PRO3S+ ELITE scan tool with newly upgraded smartlinkC V2.0. The SmartLinkC is a communication interface supporting J2534 specifications. Of course, it also can be used as a J2534 PassThru device, working together with the PC installed with the OEM diagnostic software to perform the J2534 protocol.J2534 protocol is the only solution for problems ranging from driveability and loss of power to poor fuel economy.
  • 【INTELLIGENT TOPOLOGY MAP TO FASTER FULL SYSTEMS DIAGNOSIS】 X431 PRO3S+ELITE bidirectional scan tool with new-added intuitive topology mapping. Harnesses intuitive topology mapping for comprehensive visualization of the vehicle all system. It shows all available control units in different colors, the numbers of system, the scanned system, and the scan results, bringing maximum convenience & superfast speed for you to do swift diagnosis & high-level repairs.
  • 【TOP HARDWARE CONFIGURATION, UPGRADED OF LAUNCH X431 PRO3S+】 LAUNCH X431 PRO3S+ELITE diagnostic scanner possess with Android 10.0 OS; CPU 4-Core Processor, 2.0 GHz. Greatly increased the speed of running multiple task. 2.4GHz/5GHz; 6300mAh/7.6V stronger battery capacity; 10.1 Inch Touchscreen with 8MP camera; AUTO VIN; 4GB+64GB storage memory; 20X faster transmission rate, save more vehicle documents and customer data; Supports 25+ Software Languages, such as EN, DE, FR, SP nd JP and so on.
  • 【3000+ ACTIVE TEST/BI-DIRECTIONAL CONTROL LAUNCH SCANNER】 LAUNCH X431 PRO3S+ELITE HD automotive scanner is a cost-effective bidirectional scanner that deserves owned by every repairing DIYers and mechanics. You can easily send command signal at fingertips from the scanner to various module actuators to test component integrity and functionality in minutes or even seconds to tell if replacement or repair is needed.
  • 【COMPLETE 60+ HOT RESETS, CALIBRATION, INITIALIZATION, RELEARN】 LAUNCH X431 PRO3S+ELITE SmartLinkC escaner automotriz professional enjoys 60+ special service, such as Oil Reset, ABS brake bleed, EPB, SAS, BMS, Suspension, Injector reset, Power Balance, Turbo Calibration, VGT, Transmission Adaption, Throttle Adaptation, matching and etc. rigorous on-site testing has been performed to ensure 100% availability.
Bestseller No. 3
Autel MaxiFlash Elite VCI J2534 Pass-Thru ECU Programming Tool, 2025 Multi-Protocol PassThru Interface, Work with Autel MaxiSYS Elite II Elite MS908 MS908S Pro II MS908CV II MK908P MK908 Pro II & P-C
  • 🌐【Works with Autel Elite II Elite MS908 MS908S Pro II MS908CV II MK908P MK908 Pro II】Autel J2534 work with these tools to program ECUs on specific BM.W/ BE.NZ for specific functions. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your scanner MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, contact us via: 🚘auteldirect @ outlook. com🚘.
  • 🌐【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for ToyotaeBay Techstream, Volvo VIDA, HondaeBay HDS, Jaguar-Land Rover IDS and BM.W 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
  • 🌐【High-speed Transmission Speed】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed to save more times and win more business.
  • 🌐【Multiple Devices Connected with P-C】Autel MaxiFlash Elite J2534 also supports multiple device connections to the P-C, which can operate diagnostic and reprogramming functions on more than one vehicle at the same time. Autel MaxiFlash Elite J2534 built-in wireless and data storage, which can update via Internet. It also ensures quickly reprogramming even the newest controllers.
  • 🌐【Extensive Compatibility】Autel MaxiFlash J2534 is compatible with ToyotaeBay Techstream, Volvo VIDA, HondaeBay HDS, Jaguar-Land Rover IDS and BM.W 3G for OEM diagnostics. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
Bestseller No. 4
Opus IVS CarDAQ-Plus 3 All Makes J2534 Reprogramming Tool
  • ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
  • J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
  • TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
  • J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
  • FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
Bestseller No. 5
OBDLink EX FORScan OBD Adapter
  • CUSTOM-DESIGNED FOR USE WITH FORSCAN: Works with all FORScan compatible vehicles and is recommended by the FORScan Team
  • DEALERSHIP-LEVEL DIAGNOSTICS: OBDLink EX supports all Ford protocols, modules, and advanced features of FORScan
  • ELECTRONIC SWITCH allows FORScan to access all CAN buses simultaneously and enables advanced functions not possible with “toggle switch” adapters
  • MAXIMUM THROUGHPUT -- up to 20 times faster than “toggle switch” adapters
  • ROCK-SOLID CONNECTION avoids data corruption and dropped packets
Bestseller No. 6
Autel J2534 MaxiFlash VCI, 2025 J2534 Reprogramming Tool, Pass-Thru ECU Programming Tool, DoIP/CAN FD/D-PDU 4 Channels, Work w/MaxiCOM Ultra Lite MaxiSYS Elite II Pro MS909 MS909EV MS909CV
  • 🌎【Autel All-in-1 Reprogramming Tool】As an OEM Vehicle interface for multiple makes, Autel J2534 pass-thru programmer is a multi-functional programming and communication device. Work with Autel MS909 Ultra Lite Elite 2 Pro MS909 MS909CV MS909EV to directly program on Merce.des-Be.nz & BM.W. Autel MaxiFlash VCI also works with P-C to download OEM vehicle software, seamlessly conduct OE-level diagnostic-programming-coding. Enhanced multi-protocol: SAE J2534/ CAN FD/ DoIP/ D-PDU/ RP1210, Autel Maxiflash VCI J2534 is a must have aftermarket programming device for any mechanic/ technician in the programming wo.rld!
  • 📢【Kind Tips】After purchasing the J2534, you need to update the firmware first. Steps: ✅𝟭. Access to Autel official website > click "Support" - "Download" > download "Maxi P-C Suite" APP ✅𝟮. connect J2534 and compu-ter via USB Cable ✅𝟯. Install "Maxi P-C Suite" APP on the compu-ter and update to the latest version > go to the vehicle website to purchase the corresponding OEM software for use. 📢Note: J2534 is only compatible with Windows compu-ters, and OEM software needs to be purchased.
  • 🌎【Compatible with Autel Elite II Pro Ultra Lite MS909 MS909CV MS909EV & P-C/ WIND.OWS】This 2025 latest Autel J2534 Pass-Thru VCI is 100% compatible with Autel Elite II Pro Ultra Lite MS909 MS909CV MS909EV to perform advanced functions from diagnose to programming. Besides, it can connect to P-C with Easy Steps: 1) Connect to P-C via a USB cable 2) download OEM vehicle software 3) Start Diagnose. Take For.d for example, you can download OEM software on mot.orcraft.erservi.ce website, such as: For.d Diagnostic Software downloads, As B.uilt Data, Updated Cali.bration information, then use different software do relevant features.
  • 🌎【Enhanced Protocol: CAN FD/DoIP/D-PDU/RP1210/J2534】Autel MaxiFlash JVCI is a blueto.oth communicate device, it supports latest CAN FD DoIP CAN protocols, compliant with automotive D-PDU/ J2534/ RP1210 standards. It can perform standard PassThru J2534 functions: compatible with ToyotaeBay Techstream, Volvo VIDA, Honda HDS, Jaguar Land Rover IDS and BM.W 3G for OEM diagnostics. CAN FD protocol is mainly for GM 2019+, DoIP protocol is mainly for Volvo 2018+, for L-and Rover/for Jaguar 2017+, for BM.W F chassis and G chassis.
  • 🌎【ECU Programming Coding】Tailored to ECU programming & coding, Autel J2534 Pass-Thru VCI can communicate effectively with the ECU across different vehicle makes and models. After you purchased OEM software, J2534 pass thru programmer can work with P-C: Update vehicle software to the latest version, optimize the histo.rical le.gacy of the car's old version, Replace existing software/ firmware, reprogram component after replacement.

 


Last update on 2025-04-17 / Affiliate links / Images from Amazon Product Advertising API


 

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...