“This site contains affiliate links for which OEMDTC may be compensated” |
TECHNICAL INSTRUCTIONS
FOR
SAFETY RECALL J0A/J0B/J0C
FRONT PASSENGER AIRBAG INFLATOR MODULE
CERTAIN 2003 – 2006 MODEL YEAR TUNDRA
UPDATE 10/17/2019
Update 10/17/19
− The model year has been expanded to 2006 model year
Update 6/9/19
− The scanning process has been updated Update 12/20/18
− The inflator installation procedure has been updated Update 12/18/18
− Images have been updated to reflect the new parts
BACKGROUND
The subject vehicles are equipped with front passenger airbag inflators produced by Takata. The propellant in these inflators may degrade after prolonged exposure to high absolute humidity and fluctuating high temperatures. Degraded propellant can cause the inflator to explode during airbag deployment. In the event of an inflator explosion, metal fragments could pass through the airbag cushion material, striking the vehicle occupants, and result in serious injury or death.
PARTS
Model Year | Part Number | Part Description | Quantity | ||||||
2003-2004 Tundra | 04008-03712 | INFLATOR ASSY KIT, INSTR PNL AIR BAG* | 1 | ||||||
*The kit above includes the following parts.
|
Model Year | Part Number | Part Description | Quantity |
2005-2006 Tundra | 04008-10112 | AIR BAG ASSY KIT, INSTR PNL PASS | 1 |
SEOCONTENT-START
TECHNICAL INSTRUCTIONS
FOR
SAFETY RECALL J0A/J0B/J0C
FRONT PASSENGER AIRBAG INFLATOR MODULE
CERTAIN 2003 – 2006 MODEL YEAR TUNDRA
UPDATE 10/17/2019
Update 10/17/19
− The model year has been expanded to 2006 model year
Update 6/9/19
− The scanning process has been updated
Update 12/20/18
− The inflator installation procedure has been updated
Update 12/18/18
− Images have been updated to reflect the new parts
All dealership technicians performing this recall are required to successfully complete the most current version of the E-Learning course “Safety Recall and Service Campaign Essentials”. To ensure that all vehicles have the repair performed correctly; technicians performing this recall repair are required to have successfully completed E-Learning course SC18A (if you had previously completed E-Learning Course SC13B, you do not have to take SC18A), in addition to “Safety Recall and Service Campaign Essentials”, and currently hold at least one of the following certifications levels:
• Toyota Certified (Electrical)
• Toyota Expert (Any Specialty)
• Master
• Master Diagnostic Technicians
2
I. OPERATION FLOW CHART
The flow chart is for reference only. DO NOT use it in place of the full technical instructions. Follow ALL steps as outlined in the full technical instructions to confirm the campaign is completed correctly.
3
II. BACKGROUND
The subject vehicles are equipped with front passenger airbag inflators produced by Takata. The propellant in these inflators may degrade after prolonged exposure to high absolute humidity and fluctuating high temperatures. Degraded propellant can cause the inflator to explode during airbag deployment. In the event of an inflator explosion, metal fragments could pass through the airbag cushion material, striking the vehicle occupants, and result in serious injury or death.
III. IDENTIFICATION OF AFFECTED VEHICLES
A. INVOLVED VEHICLES
• Check the TIS Vehicle Inquiry System to confirm the VIN is involved in this Safety Recall, and that the campaign has not already been completed prior to dealer shipment or by another dealer.
• TMS warranty will not reimburse dealers for repairs conducted on vehicles that are not affected or were completed by another dealer.
4
IV. PREPARATION
A. PARTS
Model Year
Part Number
Part Description
Quantity
2003-2004 Tundra
04008-03712
INFLATOR ASSY KIT, INSTR PNL AIR BAG*
1
*The kit above includes the following parts.
Inflator
1
Self Locking Nut
4
Electro Tap
1
Model Year
Part Number
Part Description
Quantity
2005-2006 Tundra
04008-10112
AIR BAG ASSY KIT, INSTR PNL PASS
1
Non-Desiccated Part Recovery
Dealers should discontinue the installation of the non-desiccated parts listed below for recall, customer pay repairs AND over-the-counter sales (if applicable).
Model
Model Year
Location
Part Number
Part Description
Qty
Tundra
2003-2004
48 States in Continental U.S.
04003-2810C
INFLATOR ASSY KIT,
INSTR PNL AIRBAG
1
USTT, Hawaii & AK
04003-1110C
2005-2006
48 States in Continental U.S.
04004-7520C
USTT, Hawaii & AK
04004-7510C
Model
Model Year
Part Number
Part Description
Tundra
2003-2004
73970-0C020-B0
73970-0C020-B1
73970-0C020-E0
AIR BAG ASSY,
INSTR PNL PASS
2005-2006
73970-0C021-B0
73970-0C021-B1
Toyota requires all dealers to return any parts listed above that still remain in dealer inventory by utilizing the Hazmat Part Return Program available. Dealers will be issued a refund for all part returns. This part return program is outlined in PANT Bulletin 2014-042.
Important Note:
In order to return the inflator, packages must NOT be opened/tampered with.
5
A. TOOLS & EQUIPMENT
• Standard hand tools
• Torque wrench
• Electrical Tape
• Molding remover set
• Techstream
• Zip Tie
OPTIONAL SST – This is an essential special service tool that the dealership should have. This tool is not mandatory when performing this repair.
Part Number
Part Name
Quantity
09890-47010-01
Anti-Static Mat Set
1
E04 CAMPAIGN TOOLS – These tools where previously provided to the dealership for campaign D0F and will be used for campaign E04. These tools are required when performing this repair.
Image
Name
Quantity
Airbag Mounting Bracket & hardware
1
Barcode Scanner
1
NOTE: These tools CANNOT be ordered through the parts or tools system. There is a very limited supply of tools, but if additional tools are needed, contact your regional representative.
6
V. SAFETY PRECAUTIONS
CRITICAL INFORMATION – READ THOROUGHLY
Failure to follow these procedures correctly could cause the SRS to unexpectedly deploy during servicing or the SRS may fail to operate correctly when required after reassembly. Confirm all work is performed as described in these instructions.
1. ELIMINATE STATIC ELECTRICITY
a) Before starting work and periodically while working on the vehicle, touch a metallic part of the vehicle to discharge static electricity in the body.
2. DO NOT MEASURE RESISTANCE
a) DO NOT measure resistance of airbag components, this may cause accidental activation.
3. HANDLE THE AIRBAG CAREFULLY
a) If an inflator is dropped, replace it with a NEW inflator.
4. DO NOT ALLOW FOREIGN OBJECTS NEAR AIRBAG
a) Be sure to collect and account for all removed nuts/bolts to prevent them from landing in the airbag assembly.
b) Any foreign objects in the airbag assembly may cause damage or injury if the airbag is activated.
5. WEAR PROTECTIVE EQUIPMENT
a) Always wear appropriate protective equipment when working on the SRS.
7
VI. SRS SYSTEM HEALTH CHECK
1. PERFORM A HEALTH CHECK
a) Confirm the Techstream is connected to the dealership’s internet.
b) When launching the Techstream software the VIN MUST be entered manually.
NOTE: All letters of the VIN MUST be entered in ALL CAPS, or the VIN will need to be reentered when running the diagnostic report.
c) Perform a health check.
Note: The VIN may auto populate on the later model year vehicles, if this happens DO NOT change the VIN.
2. RUN A DIAGNOSTIC REPORT
a) After the health check has completed, run a diagnostic report by clicking on the link on the health check screen.
NOTE: If the VIN was not entered in ALL CAPS when Techstream was launched, an error will be displayed and there will be a prompt to reenter the VIN
b) Enter the vehicle mileage and repair order information, then click the ‘report’ button.
• The VIN MAY NEED to be entered manually in ALL CAPS when launching the Techstream software. The VIN MAY NOT auto-populate on vehicles prior to the 2006 MY.
• A health check and diagnostic report with VIN MUST be performed within the last 36 hours and recorded by TMS. If the diagnostic report is not run, the healthcheck will not be recognized by TMS.
• The serial number checker application will be disabled and the inspection cannot be completed if a health check and diagnostic report is not performed and recorded by TMS.
8
VII. WORK AREA PREPARATION
CRITICAL INFORMATION – READ THOROUGHLY
The bracket assembly that was provided at the launch of SSC D0F is a critical added-safety feature that MUST be used when replacing the inflator module. Confirm the bracket assembly is installed securely in the vise and confirm the work area being used is appropriate. The anti-static mat set that is an essential SST may be available at your dealership and is optional to use during inflator replacement. If the anti-static kit is not available, before starting work and periodically while working on the vehicle, touch a metallic part of the vehicle to discharge static electricity in the body.
If the anti-static kit is not available, before starting work and periodically while working on the vehicle, touch a metallic part of the vehicle to discharge static electricity in the body.
9
VIII. FRONT PASSENGER AIRBAG ASSEMBLY REMOVAL
1. DISCONNECT THE NEGATIVE BATTERY CABLE
• Wait at least 90 seconds after disconnecting the cable from the negative battery terminal to prevent airbag and seat belt pre-tensioner deployment.
• Follow all precautions as outlined on TIS before servicing the SRS system.
2. REMOVE THE PASSENGER AIRBAG ASSEMBLY
a) Refer to TIS for instructions on airbag removal:
2003-2005
2006
b)
Tundra Standard and Access Cab
10
Tundra Double Cab
11
<Caution!>
The inflator wire harness has been
connected to the new inflator.
Don’t remove the wire harness from the inflator.
12
3. LAUNCH THE SERIAL NUMBER RECORDING APPLICATION
• The AIRBAG ASSEMBLY, ORIGNAL INFLATOR, and NEW INFLATOR serial numbers MUST be recorded using the barcode scanner (provided at the launch of SSC D0F).
• The barcode scanner application MUST be completed on every vehicle. These numbers MUST be included on every warranty claim that is submitted for inflator module replacement or the claim may be subject to debit.
• The technician performing the work MUST have valid TIS login credentials and an internet connection to perform the inspection and scanning process.
a) Log in to TIS and input the VIN of the vehicle in the Vehicle Inquiry tab.
b) Confirm the VIN is applicable and that the campaign has not been completed.
c) Click on the link to launch the serial number recording application.
d) Reenter TIS password in the serial number recording application.
NOTE: The person logged-in to TIS MUST be the person performing the repair.
e) Record the vehicle mileage into the serial number recording application.
NOTE:
• A task status screen will populate next and at other intervals during the repair. This screen will indicate if the inflator was replaced or in some limited cases that the entire airbag assembly was replaced. Click ‘next’ to proceed to the next step. This information will be used for record keeping by TMS.
• If this screen indicates that the campaign has already been completed on this VIN, there is no need to perform campaign again.
4. CONNECT THE BARCODE SCANNER
a) Connect the barcode scanner to the USB port on the Techstream.
b) The scanner will automatically connect and a beep will be heard when the scanner is ready.
NOTE:
• The scanner was originally provided for SSC D0F.
• The barcode scanner works best in low light conditions.
• Always hold the scanner directly in front of and parallel to the barcode label.
13
5. SCAN THE AIRBAG SERIAL NUMBER
ATTENTION: This information is CRITICAL
a) Scan the AIRBAG ASSEMBLY serial number 2 times.
1) Confirm the cursor is in the first serial number box then scan the serial.
2) Position the cursor in the second serial number box then scan the serial.
b) Click next.
NOTE:
• If both serial numbers that are entered do not match, confirm and reenter.
• If the serial number barcode will not scan, it can be entered manually.
AIRBAG SERIAL NUMBER IDENTIFICATION
• The airbag serial number is ALWAYS the 12 DIGITS located between the asterisks.
• The 3 digits before the asterisk ARE NOT part of the serial number, and SHOULD NOT be entered or an inaccurate response may be returned.
Airbag Serial Number Label Example
The AIRBAG ASSEMBLY serial number and the INFLATOR serial number are DIFFERENT. The AIRBAG ASSEMBLY serial number MUST be recorded prior to replacement.
14
AIRBAG ASSEMBLY SERIAL NUMBER FOR 2005 MY TUNDRA (OR SERIAL NUMBER IS MISSING OR CANNOT BE SCANNED)
If the airbag barcode cannot be scanned or is not present, check the box in the application indicating the barcode is not legible and contact your regional representative to replace the airbag assembly.
a) If the airbag serial number cannot be scanned or is not present check the box as shown below.
Checking this box requires Airbag Assembly replacement.
For 2005 MY Tundra
15
b) Scan the NEW airbag barcode in the Serial Number Recording Application.
The NEW AIRBAG ASSEMBLY serial number MUST be scanned prior to reinstallation to track the airbag assembly to the vehicle.
16
IX. INFLATOR REPLACEMENT ONLY FOR 2003-2004 MY TUNDRA
CRITICAL INFORMATION – READ THOROUGHLY
The connector of the inflator module contains a short circuiting mechanism to eliminate voltage variances when the connector(1) is disconnected. To allow for the replacement of the inflator module, a new short circuit(2) MUST be created before cutting the wires(3) and removing the inflator. The following steps MUST be followed exactly as described to ensure the work is completed correctly and safely.
17
1. MOUNT THE AIRBAG IN THE MOUNTING BRACKET
a) Position the airbag assembly so that the center mounting bracket is facing towards the ground.
b) Install the airbag to the support bars with the bolts supplied in the bracket kit.
NOTE: The airbag assembly will only fit on the support brackets one way.
c) Position the airbag so that all four stopper plate nuts can be removed through the access holes.
d) Tighten the bolts holding the support bars to the mounting bracket.
e) Confirm the following:
• Mounting bracket is secure in the vise.
• Airbag is secure in the support bars.
• The center mounting bracket on the airbag assembly is facing downward.
• Support bars are secure on the mounting bracket using 1 bolt/nut at the top of each support bar and 2 nuts/bolts at the bottom of each support bar.
CRITICAL INFORMATION – READ THOROUGHLY
ALWAYS keep as much of your body as possible in front of the bracket when working on the airbag assembly.
Remember to periodically touch a metallic part of the vehicle to discharge static electricity in the body if the anti-static kit is not being used.
2. PREPARE TO INSTALL THE SHORT CIRCUIT
a) Cut the yellow corrugated tube on the harness approximately 4 inches (10 cm) using nippers.
• DO NOT damage the wires in the tube.
• DO NOT use a knife or razor blade to cut the tube to avoid damaging the wires.
• This may be performed on either end of the inflator.
b) Cut off the tab of the electro tap shown in the illustration.
NOTE: The electro tap is included in the inflator parts kit.
This tab MUST be removed to ensure a good short.
18
3. CREATE A NEW SHORT CIRCUIT IN THE INFLATOR HARNESS
a) Place one wire in the electro tap as shown in the illustration.
b) Fold and pinch the half of the electro tap with the wire and use pliers to lock the electro tap.
NOTE:
• DO NOT work on both wires at the same time to avoid errors.
• Pliers MUST be used to confirm the electro tap is firmly locked in place.
c) Set the other wire in the electro tap and lock it in place using pliers.
DO NOT measure resistance of the inflator wires, this may cause accidental activation.
4. CUT THE INFLATOR WIRES
a) Cut the 2 wires at the side of the electro tap that is farthest away from the inflator.
Cut the wires opposite the inflator
DO NOT measure resistance of the inflator wires, this may cause accidental activation.
19
5. REMOVE THE SELF LOCKING NUTS
a) Use the access holes in the bracket to remove the 4 nuts.
NOTE:
• DO NOT use power tools.
• The bracket support bars may need to be repositioned to remove the nuts through the access holes.
b) Remove the stopper plate and place in a secure location because it will be reused.
DO NOT discard the Stopper Plate, it will be reused.
c) Discard the 4 nuts as they are not to be reused.
NOTE: DO NOT reuse the old nuts, new nuts MUST be used.
6. REMOVE THE INFLATOR
a) Gently push in the 4 studs to loosen the inflator for removal.
b) Remove the inflator from the airbag assembly and place it on a safe work surface.
20
ENSURE YOU ENTER BOTH THE OLD AND NEW INFLATOR SERIAL NUMBERS IN THE APPROPRIATE SPOT OF THE APPLICATION
7. SCAN THE OLD AND NEW INFLATOR SERIAL NUMBER
a) Scan the OLD inflator serial number and mark the old inflator so that it will not be reused.
b) Scan the NEW inflator serial number.
ATTENTION: This information is CRITICAL
• It is used to confirm the correct inflator is removed from the vehicle.
• It is recorded by TMS to trace the return parts shipment.
• It is used to track the new inflator that is being installed in the vehicle.
Depending on the serial data scanned during a previous Takata repair, you may NOT be asked to enter an Original Inflator Serial Number
21
c) If the inflator serial number cannot be scanned or is not present check the box as shown below.
Checking this box requires Airbag Assembly replacement.
**Note** Contact your region in the event
that you are unable to read the serial number.
DO NOT ATTEMPT TO INSTALL INFLATOR
NOTE: The NEW AIRBAG ASSEMBLY serial number MUST be scanned prior to reinstallation to track the airbag assembly to the vehicle (refer to page 14).
d) Confirm agreement by checking the two boxes in the lower left hand corner of the screen.
e) Record the Warranty Authorization # to be included in the warranty claim.
f) Place the old inflator in the parts box and take it immediately to the parts department.
NOTE:
• Confirm the cursor is in the correct serial number input box before scanning.
• If the serial number barcode will not scan, it can be entered manually.
• If there are any difficulties or concerns with this process, email quality_compliance@toyota.com with details.
22
Step d)
Step e)
8. REMOVE NEW INFLATOR CONNECTOR COVER
a) Carefully use a pocket screwdriver to disengage the first release tab as shown in the image
b) Carefully use a pocket screwdriver to disengage the second release tab as shown in the image
c) Open the connector cover. Once open carefully use a pocket screwdriver to disengage the release tab and remove the connector cover from the connector
23
9. INSTALL THE NEW INFLATOR
a) Route the inflator wire harness through the stopper plate
b) Carefully slide the new inflator into the airbag assembly.
c) Confirm the harness is not pinched by the stopper plate
10. REINSTALL THE INFLATOR CONNECTOR COVER
d) Install the connector into the connector cover. Ensure the release tab on the connector is engaged into the connector cover.
e) Once the connector is installed into the connector cover, close the connector cover over the connector.
f) Wrap electrical tape around the connector to prevent the connector from opening.
24
11. CONFIRM THE INFLATOR ALIGNMENT
a) Align the flat on the inflator with the flat on the airbag assembly bracket.
Confirm the flats on the airbag assembly and inflator are aligned.
12. REINSTALL THE STOPPER PLATE.
g) Place the stopper plate on the airbag assembly.
The inflator stopper plate is reused at this step; a new one is not included in the inflator kit.
h) Install stopper plate nuts (NEW) by hand. They will be torqued on a later step.
i) Install the NEW nuts on the airbag assembly bracket by hand. They will be torqued on a later step.
13. TORQUE THE PLATE NUTS
a) Tighten the nuts evenly in two increments following the sequence shown in the illustration. Use a socket driver or torque wrench to tighten the nuts.
Torque: 35in. lbf (3.9N∙m)
• There will be some resistance when tightening the nuts because they are self-locking, confirm the nuts are tightened correctly.
• DO NOT use a power tool, T-handle, or ratchet when tightening the nuts to avoid over torqueing.
25
14. REMOVE THE AIRBAG ASSEMBLY FROM THE BRACKET
a) Remove the two bolts and the airbag assembly, then place the assembly on a cloth or the anti-static mat if it being used.
15. INSPECT THE AIRBAG BEFORE INSTALLATION
a) Confirm that the 4 NEW nuts are installed and tight.
b) Confirm the stopper plate is reinstalled.
c) Confirm the flats on the airbag assembly bracket and inflator are aligned.
d) Confirm the inflator harness connector is secure and installed in the correct direction.
e) Confirm that the harness is engaged in the clamp.
X. FRONT PASSENGER AIRBAG ASSEMBLY INSTALLATION
1. REINSTALL THE AIRBAG ASSEMBLY
Note: During reinstallation of the airbag assembly, ensure the 12mm bolt and two 10mm nuts securing the airbag assembly to the instrument panel are installed and torqued to the required specification identified on TIS.
c) Refer to TIS for instructions on airbag installation:
2003-2005
2006
2. RECONNECT THE NEGATIVE BATTERY CABLE
3. PERFORM A HEALTH CHECK AND DIAGNOSTIC REPORT
NOTE: Enter the VIN when performing the health check in order for the data to be recorded by TMS.
26
◄ VERIFY REPAIR QUALITY ►
− Confirm all precautions are follow to ensure safety during the repair
− Confirm the entire serial number checker application is completed and the warranty authorization # is recorded on EVERY vehicle
− Confirm the old inflator is handled safely and given to the appropriate parts professional for shipment
− Confirm the inflator harness connector is fully engaged and that the stopper plate is installed correctly
If you have any questions regarding this update, please contact your area representative.
XI. APPENDIX
A. CAMPAIGN DESIGNATION DECODER
C0TYear Campaign is Launched8 = 20089 = 2009A = 2010B = 2011C = 2012 D = 2013E = 2014F = 2015Etc…Repair Phase1st Campaign = A2nd Campaign = BEtc…Current Campaign Letter for this year 0 = Remedy1 = Prelim/Interim 2 = Prelim/Interim for Phase 2 Vehicles(Remedy not yet available) “1 or 2” will change to “0” when the Remedy is available
B. CAMPAIGN PARTS DISPOSAL
ALL inflators that are removed from vehicles under this campaign MUST be packaged and shipped back to the inflator manufacturer following the manufacturer’s instructions. The instructions can be found in the following locations:
• Attached to the dealer letter
SEOCONTENT-END
Remedy Instructions and TSB
RCRIT-19V741-9869.pdf 3681.185KB
- 【Buy with Confidence】 As a America's No.1 diagnostic tool brand, Innova stands for innovation, quality, and accessibility in the automotive diagnostic industry. We are known for developing cutting-edge diagnostic tools that are user-friendly, reliable, and made for US by Americans.
- 【Unleash Your Drive's Potential】Much more than a car code reader, the 6100P scanner effectively reads and erases engine, ABS, SRS, and transmission codes for popular US car makes such as Ford, Chevy, Dodge, GM, etc. When the traction light is constantly on, the ability to really detect where the problem is concerning brakes and airbags enables you to make sure all safety measures in place before putting yourself in harm's way.
- 【Your Car's Health Doctor】Easily view procedures or send commands for oil change, mileage or driving time reset for most 1996 and newer OBD2 vehicles. It also monitors your oil level and oil life status, ensuring optimal vehicle health.
- 【alternator Test】The Innova 6100P scanner is perfect for assessing the performance of the alternator in your hybrid, car, SUV, minivan, or light truck diesel as well. During rough winters and scorching summers, this diagnostic tool will be invaluable when trying to root out start-up issues.
- 【Drive with Confidence and Peace】Quickly identify if your vehicle needs immediate attention with our Code Severity Levels function. This feature helps you understand whether you need to fix an issue immediately or if it can wait until you get home, keeping warning lights at bay.
- 🎉【2024 Upgraded Ver. of AL519/ ML519/ ML619】Autel develops the brand-new AutoLink AL619 as the advanced ver. of Autel ML519, AL519, AL319, MS309. This AL619 OBD2 scanner can scan ABS & SRS systems, and support 10 Modes of OBD II Diagnostics Function on Worldwide Vehicles to read, erase codes and turn off the MIL, ABS, SRS warning lights so that you can better maintain your car when related malfunctions occur and make your vehicle ready for the annual test.
- 🎉【Accurate ABS/ SRS Diagnostics Functions】The ABS/ SRS diagnostic function is used to retrieve and clear codes from the ABS/ SRS systems. It can read and clear DTCs, show definitions of each code, display live data of multiple sensors in the graph to locate fault causes, and assist home mechanics to do the proper repair and clear ABS & Airbag warning lights. Diagnoses ABS/ SRS system codes on most 1996 and newer major vehicle models. Please email 📩 immoautel @ outlook. com 📩 for help.
- 🎉【All 10 Modes of OBD II Diagnostics Function】The OBD II Diagnostics function is a fast-access option that allows you to carry out a quick test on the engine system of OBD II vehicles. Read Codes, Erase Codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, DTC Lookup, Component Test, Viewing Vehicle Information, Modules Present.
- 🎉【Live Data and Freeze Frame Data】With Live Data functions, Autel AL619 OBD2 diagnostic code reader allows you to view the live PID (Parameter Identification Data) of the vehicle's computer module(s) in text, graph to check the status of various sensors. And Freeze Frame Data enables you to view the vehicle's operating parameters at the moment a DTC is detected. These information will aid the technician by allowing the parameters to be duplicated for diagnostic and repair purposes.
- 🎉【DTC Lookup Feature】Besides showing you the code’s definition while you are reading the diagnostic trouble codes, AL619 features comparably user-friendly DTC Lookup Function which enables you to retrieve the definitions of any error codes from the large database of AL619, saving you from the hassle of wasting time searching definition of every code via Google.
- 5 IN 1 DIAGNOSTIC SCANNER: This is an OBDII scanner and 4 systems diagnostic tool. The AUTOPHIX 3210 PRO Bluetooth Auto Scanner not only has OBDII diagnostic function, but can also be used as an ABS/SRS/transmission scanner and check engine code reader. When it is an OBD2 scanner, you can use it to check if your car is ready for annual test via I/M preparation menu. In addition, the built-in DTC library, live data stream, data playback, performance testing and many more such functions are supported by it.
- RELIABLE CAR HEALTH MONITOR: Are you confused when the ABS/SRS/Transmission/Check Engine warning light is blinking? The AUTOPHIX 3210 PRO Bluetooth Scanner will help you to do a thorough scanning and inspecting of your car and find out the root cause, which saves your time and money. Tip:The warning light will be turned off after the problem is solved. Airbag crash/collision data cannot be cleared, even if you replace the airbag with a new one.
- QUICK DIAGNOSIS: The 3210 PRO is the newest 2024 Enhanced 4-System Bluetooth Code Reader that retrieves vehicle information, reads/clears trouble codes, and displays a 4-in-1 live data stream. You'll easily find out what's wrong with your car. In just a few minutes, you'll be in control of your car!
- EXCLUSIVE APP: Are you tired of the following with third party apps? For example: 1.need to download different apps for different cars? 2. require extra download fees? 3. only support a few functions? 4. can only use one of Android and iOS? Now!One AUTOPHIX 3210 PRO Scanner is enough to solve all the above problems. The must-have wireless/bluetooth automotive diagnostic tool/code reader for today's car owners. iPhone iOS, iPad, Android can be downloaded for free without any additional subscription fees.
- ADVANCED DATA FLOW DISPLAY:AUTOPHIX 3210 PRO Bluetooth code reader allows you to graphically display your vehicle's data flow instead of boring text, including engine coolant temperature, engine RPM, vehicle speed, absolute throttle position, control module voltage, etc. You can view different parameter values corresponding to different times. The advanced data streams provide useful information for entry-level professionals and diyers who can troubleshoot vehicle problems quickly and efficiently.
- 🎄【Easy to Use--Work out of box】+【FOXWELL 2024 New Version】 FOXWELL NT604 Elite scan tool is the 2024 new version from FOXWELL, which is designed for those car owners who want to figure out the cause issue before fixing the car problem via scanning the most common systems like abs srs engine and transmission.The NT604 Elite diagnostic tool comes with latest software, which can be used out of box. No need to waste time to download the software first.
- 🎅【Affordable】+【Reliable Car Health Monitor】 Will you be confused what happen when the warning light of abs/srs/transmission/check engine flashes? Instead of taking your cars to dealership, this foxwell scanner will help you do a thorough scanning and detection for your cars and pinpoint the root cause. It will t-urn off the warning light car after the problem is fixed.👉TIPS: Airbag crash/collision data can NOT be cleared even you replace the new airbag.
- 🎄【5 in 1 Diagnostic Scanner】Compared with those auto scanners (50-100), NT604 Elite code scanner not only includes their OBDII diagnosis but also it can be an abs/srs scanner, transmission and check engine code reader. When it’s an odb2 scanner, you can use it to check if your car is ready for annual test through I/M readiness menu. In addition, live data stream, built-in DTC library, data play back and print, all these features are a big plus for it.
- 🎅【Fantastic AUTOVIN】+【No extra software fee】Through the AUTOVIN menu, this NT604 Elite car scanner allows you to get your V-IN and vehicle info rapidly, no need to take time to find your V-IN and input one by one. What's more, the NT604 Elite abs srs scanner supports 60+ car makes from worldwide (America/Asia/Europe). You don’t need to pay extra software fee.
- 🎄【Solid protective case KO plastic carrying bag】+ 【Lifetime update】Almost all same price-level obd scanner diagnostic tool only offers plastic bag to hold on the scanner.However, NT604 Elite automotive scanner is equipped with solid protective case, preventing your obd2 scanner from damage. Then you don’t need to pay extra money to buy a solid toolbox.
- 2024 Best Choice for ABS Bleeder Scan Tool - Was the brake pedal always slowly sinking down or becoming loose? This abs brake bleeding scan tool will bleed the brake system by cycling the pump and valves to achieve a tight brake pedal. It's the most affordable obd2 scanner with abs auto bleed function you can find. With the clear step by step instruction, even a beginner can use it. Coverage check on FOXWELL official site: Support- Diagnostic Coverage List.
- More Than a Entry Level OBD Scanner, Ideal for Home Mechanics - Based on the NT301 FOXWELL Scanner, NT630 Plus takes OBD diagnostics to the next level by customizing all functions for ABS and SRS systems. This srs abs scanner provides in-depth insights on error code diagnosis, wheel speed sensor live data, airbag circuits and cable connectors monitor, module activation and etc. It's an total game-changer in resolving ABS SRS issues.
- No More Higher End Service than You Needed - One NT630 Plus is enough! This obd2 scanner with abs and srs takes depth diagnosis on Anti-Lock Brake System & Supplemental Restraint System, and also performs daily required resetting services which same priced scanners cannot do. Like Airbag light reset/ SAS(Steering Angle Sensor) adjustment/ Oil light reset and EPB service functions. this car scanner will help the part to operate normally after the faults repaired.
- Also can Work like NT301 - The NT630 Plus abs code reader connect to the OBD2 port directly. It will diagnose all obd2 modules instantly, displays the live data, locates bad sensors and I/M readiness status before the annual inspection. Guides you to do the maintenance work, reduces the potential driving risk and keep a peak performance on the road.
- Complicate? Unreadable? - Intuitive LCD display with clear operate instructions, even a beginner can diagnose the car faults with the NT630 Plus. Ergonomic Touch with anti-collision and anti-slip cover design, comfortable for daily car diagnose work. Unique button press sound will provide the overall tactile and visual experience to notice you a task has been completed or a command has been executed.
- 🔧【PLUG AND PLAY - EASY TO USE】 : ANCEL FX2000 car scanner only takes 3 steps to connect to the car for diagnosis without cumbersome operations. The latest FX2000 scan tool is equipped with a one-key diagnosis function, which can automatically identify the model and year of your car, and automatically diagnose the car. Even beginners can use it to read the data and find out what the fault codes mean.
- 🚗【FULL OBD-LEVEL DIAGNOSTICS TOOL】: Quickly determines the cause of engine system faults, reads current, permanent and pending codes. After the repair, clears the codes and turns off the warning light. In addition, the FX2000 engine code reader also displays important OBD II advanced data such as fuel, live data and other manufacturer-specific parameters in real time to ensure that the engine ECU is operating correctly and safely, saving vehicle owners a lot of time and money in maintenance.
- 🚙【TRANSMISSION FAULT DIAGNOSTIC TOOL】: Some noises come from the transmission? Ancel obd2 scanner will read fault codes, display live transmission system data (fluid temperature, fluid pump, clutch actuation, pressure, etc.), and ensures transmission performance is optimal for vehicle speed and load. It provides detailed TCM data of the vehicle, so you can quickly and accurately find existing or potential problems.
- 🚐【FIND OUT SRS WRONG】: ANCEL FX2000 automotive scanner is able to read and clear fault codes in the SRS (airbag) and turn off the warning light to make sure the system is working correctly and safely. This odb2 scanner also displays a live graphical data stream of the supplemental restraint system (air bag), which allows you to analyze and verify that the air bag system is working properly.
- 🚌【ABS OBD2 SCANNER】:The FX2000 diagnostic scanner for all vehicles can read and clear the Diagnostic Trouble Codes (DTC) data stream transmitted from the ABS. By retrieving the ABS code data, the obd scanner can check the various brake components and accurately diagnose problems.
- SIMPLIFYING CAR REPAIR - Our goal is to simplify your car repair process. Our device turns your smartphone into a powerful OBD2 scanner diagnostic tool, allowing you to quickly understand your vehicle's problem, view recommended fixes, and purchase the necessary parts for repair.
- EXPERIENCE PROFESSIONAL DIAGNOSTICS - BLCKTEC's enhanced vehicle diagnostics gives you access to advanced features typically found only on high-end scanners. With our car code reader you can read and clear engine codes, ABS (brakes), SRS (airbags), TPMS codes, and many more.
- RELIABLE AND ACCURATE RESULTS - Our car scanner utilizes the latest OBD2 technology to provide accurate and reliable diagnostic information, ensuring that you can trust the results you receive.
- COMPATIBLE WITH A WIDE RANGE OF VEHICLES - Our bluetooth OBD2 scanner works with most vehicles made after 1996, including cars, trucks, and SUVs, making it a versatile tool for any DIYer.
- USER-FRIENDLY APP - Our accompanying app is easy to use and navigate, with clear and concise information displayed in an easy-to-understand format. Available on IOS and Android.
- [ABS & SRS Scanner with Active Test] The ABS/ SRS diagnostic tool Read & clear DTCs, displays live data in a graph to locate the cause of faults and assists the home mechanic with repairs and clearing ABS and airbag warning lights. Active test sensors, valves or solenoids etc. and tracks any threats in real time. It is invaluable to have a diagnostic tool with Active Test feature that you will never find on similar ABS/ SRS scanners.
- 【3 HOP Reset Services 】Easy to set up 3 regular reset services for Oil Light, Battery Management System, and Steering Angle Position. With this obd2 scanner, you can reset the oil service light and reset pre-programmed mileage intervals for energy efficiency; adjust or reset the steering angle position to keep steering aligned; and clear the original low battery fault information. No need to leave home for shop-quality car maintenance.
- 【All OBD2 Test Modes 】 This ABS & SRS scan tool is also a full featured obd2 code reader, allowing a quick test of the engine system of OBD II vehicles, can Read/Clear engine light codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, Evap Test, Read Vehicle Information, and help pass smog test for most post-1996 OBD2/CAN vehicles.
- [DTC LookUp Library] Can't read the code? Go to the DTC LookUp Library. The Topdon AL600 OBD2 scanner offers a wealth of code definitions so you don't have to look them up in a list or database, and the HELP function takes you to diagnostic tips for possible fixes, saving time searching for repair materials online. No other scan tool or code reader under $100 offers this level of assistance.
- [User-Oriented] You'll love the feel of this automotive scanner, with black rubber grips all around the outer edges for durability and to withstand accidental drops. With its easy access menu, you can operate all functions in minutes with just a few button presses. The 3-color LEDs give you a intuitive indication of the OBD2 test results in a second. 3 shortcut keys, one key to read/clear DTCs and a one-touch smoke status check make it easy to use even for beginners.
- [🔥🔥Oil/SAS/Throttle Reset] New 3 reset functions are available! TOPDON ArtiDiag500 OBD2 scanner with Oil /SAS/Throttle Reset to maintain your vehicle systems safely. 🚩Just Click "Upgrade" to obtain 3 special reset functions.
- 🚗[OBD2 Scanner] The TOPDON OBD2 scanner performs all ENG/AT/SRS/ABS diagnostics with 4-in-1 graphic live data. 🚩It covers all OBD2 tests for 60 manufacturers and 10000+ model. It also features 5-second one-touch AutoVIN, 🚩a free one-touch lifetime upgrade through WiFi, library DTC, 9 languages, 🚩printable auto-generated report with email sharing, 🚩smooth Android 7.0, 16GB ROM, 🚩vivid 5-inch touchscreen, and up to 10 hours of battery life.
- [🔥🔥4 Car System Code Reader] The TOPDON OBD2 scanner accesses 4 systems: 🚩Engine/ABS/SRS/Transmission. It identifies the ECU version, pull DTCs with 4-in-1 graphic live data and DTC explanation to identify issues, erase DTCs to turn off the warning lights after repair (For cars made in 2005 and newer). In order to help you extend the lifespan of your vehicle while improving performance, this code reader also includes all obd2 test modes to solve the major concerns for all vehicles.
- 🚗[User-Oriented TOPDON OBD2 Scanner] With this scan tool's touchscreen and rubberized buttons, you may easily navigate through menus or process while following a logical path even when wearing gloves. With 16GB on-board memory, the scanner enables for the recording of several diagnostic reports, which can be shared via email and printed for review. Along with this, you can 🚩upgrade your software for free for lifetime with one-touch over Wi-Fi for that help update the features and expanding car coverage.
- 🚗[Multiple Functions] The Smart AutoVIN of this TOPDON OBD2 scanner keeps track of your manual selections for vehicle make, model, and year and directs you to the suitable diagnostics. 🚩Max 4 Live Data streams integrated for much easier data processing. Diagnostic feedback online with this diagnostic tool to help you get tough repair operations well-completed. Real-time car battery voltage monitoring identifies probable vehicle defects.
- [COMPATIBLE FOR BMW] - As what you've seen, we have a variety of OBD2 code readers compatible for BMW and MINI, C410 is one of the most cost-effective scan tools fit for BMW and MINI vehicle owners. C410 Supports most BMW and MINI after 2001. 1997-2004 cars need a 20 pin adaptor (not included).
- [FIT FOR BMW AND MINI] - Compatible ECU systems including Drive, Chassis and Body all system. Supported function including read and clear trouble codes, display live data stream, graph display, vehicle version information, clear adaptation, CBS reset and reset Engine oil.
- [EASY TO OPERATE] - C410 car diagnostic tool via 2.4" TFT 240K true color LCD display screen to indicates the test results , with the silicone keypad you can easy to access the each of menu options, Rugged drop-proof case Prevent falling, the menu layout on the screen is easy to understand and you will no trouble to figuring out how to do what you needed.
- [LIFETIME FREE UPDATE] - Many OBDII scanners for BMW require to pay an additional fee for new upgrades after the warranty period has expired. C410 supports lifetime free software upgrades, new parameters, functions and the latest vehicle data are constantly updated via the USB port over the Internet. Just a few easy steps, the scanner will always be up to date with the latest system within minutes.
- [ATTENTION PLEASE!!!] - Battery registration function does not support cars before 2004 and also does not support the E chassis (3 Series_E46, 5 Series_E39, 7 Series_E38, X3_E83, X5_E53, Z3_E36, Z4_E85/E86, MINI_R50/R51/R52/R53). For the above chassis models, you just need to replace the battery directly, because these models do not require battery registration. In addition, the battery registration function only for the same type and capacity battery. Inconsistent battery type or capacity can lead to registration failure.
Last update on 2024-03-22 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.