“This site contains affiliate links for which OEMDTC may be compensated” |
IMPORTANT UPDATE
TECHNICAL INSTRUCTIONS
FOR
SAFETY RECALL 20TA02
VEHICLE MAY STALL DURING DRIVING AT HIGHER SPEED
2018 – 2019 Sequoia | 2018 – 2019 Camry | 2019 Avalon |
2018 – 2019 Tundra | 2014 FJ Cruiser | 2014 4Runner |
2018 – 2019 Corolla | 2018 – 2019 Highlander |
The remedy for this campaign is being launched in phases. Confirm remedy eligibility on each VIN in TIS before starting any repairs.
Update 6/24/2020: Corolla and Highlander have been added
The repair quality of covered vehicles is extremely important to Toyota. All dealership technicians performing this recall are required to successfully complete the most current version of the E-
Learning course “Safety Recall and Service Campaign Essentials”. To ensure that all vehicles have the repair performed correctly; technicians performing this recall repair are required to currently hold at least one of the following certification levels:
- Certified (any specialty)
- Expert (any specialty)
- Master
- Master Diagnostic Technician
It is the dealership’s responsibility to select technicians with the above certification level or greater to perform this recall repair. Carefully review your resources, the technician skill level, and ability before assigning technicians to this repair. It is important to consider technician days off and vacation schedules to ensure there are properly trained technicians available to perform this repair at all times.
PREPARATION
PARTS
Because of the extensive list of parts for the numerous models affected by this Safety Recall, a website has been created to detail the required parts for each vehicle. Reference the following website for a detailed parts list for each specific VIN:
To log into the website:
- Enter your dealer code in the Dealer Code field.
- Enter XXXXX (5 Capital X’s) for the Password.
Note: Warranty will only reimburse dealers for the part numbers listed on the website. Any other part numbers will not be accepted on the campaign claim.
TOOLS & EQUIPMENT
- Standard Hand Tools
- Torque Wrench
- Air Blow gun
- Gas Caddy (minimum 25 gallon capacity)
MATERIALS
- Brake Cleaner
CAMPAIGN TOOLS
Prior to the launch of this Campaign, each dealership will receive a Crossbar and a set of Cam Lock Retainer Jaws for removing the Cam Lock type retainer rings. These jaws will be used with the dealerships existing Handle set from the Fuel Sender Lock Nut Wrench Set (09808-14031). A 1/2” breaker bar can also be used. This set of tools will supplement the SST kit that each dealership currently has. The Campaign tools were sent directly to the dealership’s Service Manager. Additional SST’s can be purchased through the Toyota Special Service Tools (SST) website.
In the affected models, there are three different types of Fuel Pump Retainer Rings. Reference the following chart to determine the proper SST or campaign tool for each model and retainer type.
BACKGROUND
The subject vehicles are equipped with a low-pressure fuel pump which may stop operating. If this were to occur, warning lights and messages may be displayed on the instrument panel, and the engine may run rough. This may result in a vehicle stall, and the vehicle may be unable to be restarted. If a vehicle stall occurs while driving at higher speeds, this could increase the risk of a crash.
SAFETY PRECAUTIONS
CAUTION:
- When installing/uninstalling the fuel system components, keep safety first in mind and carefully observe the following instructions to avoid accidents:
- When working on the fuel system, display a Flammable – Keep Fire Away sign.
- Smoking is prohibited nearby.
- Perform this work in an area where there are no sparks nearby from the operation of welders, grinders, drills, electric motors, stoves, etc.
- DO NOT use electrical devices nearby because they can become hot and the operation of power switches can generate sparks.
- DO NOT use iron or steel hammers while working, because they may generate sparks.
- DO NOT start engines even in adjacent stalls.
- Prepare fire extinguishers before starting any work.
- Perform this work in a well-ventilated area (natural ventilation). DO NOT use exhaust fans or electric fans, because their motors might generate sparks.
- Since it is possible for fuel vapor to build up, DO NOT work in or near a pit.
- If fuel is spilled, use shop towels or similar material to quickly wipe it up and then use compressed air to diffuse the fuel vapor.
- Shop towels and other materials that have come into contact with fuel should be dried in a well ventilated area and then disposed of as appropriate.
SEOCONTENT-START
IMPORTANT UPDATE
TECHNICAL INSTRUCTIONS
FOR
SAFETY RECALL 20TA02
VEHICLE MAY STALL DURING DRIVING AT HIGHER SPEED
2018 – 2019 Sequoia
2018 – 2019 Camry
2019 Avalon
2018 – 2019 Tundra
2014 FJ Cruiser
2014 4Runner
2018 – 2019 Corolla
2018 – 2019 Highlander
The remedy for this campaign is being launched in phases. Confirm remedy eligibility on each VIN in TIS before starting any repairs.
Update 6/24/2020: Corolla and Highlander have been added
The repair quality of covered vehicles is extremely important to Toyota. All dealership technicians performing this recall are required to successfully complete the most current version of the E-Learning course “Safety Recall and Service Campaign Essentials”. To ensure that all vehicles have the repair performed correctly; technicians performing this recall repair are required to currently hold at least one of the following certification levels:
• Certified (any specialty)
• Expert (any specialty)
• Master
• Master Diagnostic Technician
It is the dealership’s responsibility to select technicians with the above certification level or greater to perform this recall repair. Carefully review your resources, the technician skill level, and ability before assigning technicians to this repair. It is important to consider technician days off and vacation schedules to ensure there are properly trained technicians available to perform this repair at all times.
2
I. OPERATION FLOW CHART
Verify Vehicle Eligibility
1. Confirm vehicle VIN matches the RO.
2. Check for Campaign eligibility using TIS.
No further action required.
Not
Covered
Covered
Campaign complete.
Return the vehicle to the customer.
Remove Fuel Suction
Tube Assembly from vehicle
Disassemble Fuel Suction
Tube Assembly
Install NEW fuel pump
Reassemble Fuel Suction
Tube Assembly
Reinstall Fuel Suction Tube
Assembly into vehicle
Check the Campaign Status of the VIN to
determine if Remedy is available
Remedy Available
The Remedy for this vehicle
is not available at this time.
Refer to the Toyota Dealer
Letter for Remedy Launch
timing for this model.
20TA02 Dealer Letter
..Remedy Not..
Available
3
II. IDENTIFICATION OF AFFECTED VEHICLES
1. CHECK VEHICLE FOR CAMPAIGN ELIGIBILITY
a. Compare the vehicle’s VIN to the VIN listed on the Repair Order to ensure they match.
b. Check the TIS Vehicle Inquiry System or Service Lane to verify this vehicle is eligible for
Safety Recall 20TA02.
c. Determine the Campaign Status for Safety Recall 20TA02.
What is the Campaign Status of
Safety Recall 20TA02 for this vehicle?
DO NOT PROCEED!! Check the
VIN again at a later date for
Remedy availability.
Continue to Section III.
PREPARATION on p.4
..Remedy Available.. ..Remedy NOT Available..
DO NOT PROCEED with these instructions if the
Campaign Status shows Remedy Not Available!
The remedy for this campaign is being launched in phases. Confirm remedy eligibility on
each VIN in TIS before starting any repairs.
Launch timing specific to each model is available in the 20TA02 Dealer Letter.
Note: Warranty will not reimburse dealers for repairs completed on vehicles that are not affected or
were previously completed, even by another dealer. In addition, warranty claims will not be
processed for vehicles that are not yet eligible for the remedy.
4
III. PREPARATION
A. PARTS
Because of the extensive list of parts for the numerous models affected by this Safety Recall, a website has been created to detail the required parts for each vehicle. Reference the following website for a detailed parts list for each specific VIN:
https://20ta02.imagespm.info
To log into the website:
a. Enter your dealer code in the Dealer Code field.
b. Enter XXXXX (5 Capital X’s) for the Password.
Note: Warranty will only reimburse dealers for the part numbers listed on the website. Any other part numbers will not be accepted on the campaign claim.
B. TOOLS & EQUIPMENT
• Standard Hand Tools
• Torque Wrench
• Air Blow gun
• Gas Caddy (minimum 25 gallon capacity)
C. MATERIALS
• Brake Cleaner
D. CAMPAIGN TOOLS
Prior to the launch of this Campaign, each dealership will receive a Crossbar and a set of Cam Lock Retainer Jaws for removing the Cam Lock type retainer rings. These jaws will be used with the dealerships existing Handle set from the Fuel Sender Lock Nut Wrench Set (09808-14031). A 1/2” breaker bar can also be used. This set of tools will supplement the SST kit that each dealership currently has. The Campaign tools were sent directly to the dealership’s Service Manager. Additional SST’s can be purchased through the Toyota Special Service Tools (SST) website.
Campaign Tools
Special Service Tools
Cam Lock Retainer Jaws
Handle
09808-01010
Or suitable 1/2” breaker bar
Crossbar
Used With
5
C. Special Service Tools
In the affected models, there are three different types of Fuel Pump Retainer Rings. Reference the following
chart to determine the proper SST or campaign tool for each model and retainer type.
RETAINER TYPE
Type:
Bolt In
Cam Lock
Plastic Ring
Plastic Ring
w/ Holding Tool
SST:
No SST
Required
Fuel Sender Lock Nut Wrench
Kit
(09808-14031)
Claw: 105mm Jaw Set
(09808-01070)
Crossbar
(09808-01030)
Fuel Sender Lock Nut Wrench
Kit (09808-14031)
Option 1: Claw: 50mm Jaw
Set
(09808-01040)
Option 2: Claw: Sliding jaw
(09808-01080)
Crossbar
(09808-01030)
Fuel Pump Retainer Tool (*e)
(09808-14040)
Fuel Pump Holding Tool (*d)
(09808-14050)
Special
Notes:
Campaign Tool:
Cam Lock Retainer Jaws
Requires use of the Handle
from the Fuel Sender Lock Nut
Wrench Kit, or a 1/2” breaker
bar.
Aftermarket
alternative:
CTA Tools 1044
Fuel Tank Lid Wrench
This tool is available
from Autopart.com
Or contact CTA Tools at
info@ctatools.com for
purchasing inquiries
Additional SST’s can be
purchased from the
Toyota Special Service
Tools (SST) website
Models
Avalon (2018) Avalon (2019) 4Runner Highlander
Camry Sequoia
Tundra
FJ Cruiser
Corolla
6
IV. BACKGROUND
The subject vehicles are equipped with a low-pressure fuel pump which may stop operating. If this were to occur, warning lights and messages may be displayed on the instrument panel, and the engine may run rough. This may result in a vehicle stall, and the vehicle may be unable to be restarted. If a vehicle stall occurs while driving at higher speeds, this could increase the risk of a crash.
V. SAFETY PRECAUTIONS
CAUTION:
When installing/uninstalling the fuel system components, keep safety first in mind and carefully observe the following instructions to avoid accidents:
a. When working on the fuel system, display a Flammable – Keep Fire Away sign.
b. Smoking is prohibited nearby.
c. Perform this work in an area where there are no sparks nearby from the operation of welders, grinders, drills, electric motors, stoves, etc.
d. DO NOT use electrical devices nearby because they can become hot and the operation of power switches can generate sparks.
e. DO NOT use iron or steel hammers while working, because they may generate sparks.
f. DO NOT start engines even in adjacent stalls.
g. Prepare fire extinguishers before starting any work.
h. Perform this work in a well-ventilated area (natural ventilation). DO NOT use exhaust fans or electric fans, because their motors might generate sparks.
i. Since it is possible for fuel vapor to build up, DO NOT work in or near a pit.
j. If fuel is spilled, use shop towels or similar material to quickly wipe it up and then use compressed air to diffuse the fuel vapor.
k. Shop towels and other materials that have come into contact with fuel should be dried in a well-ventilated area and then disposed of as appropriate.
7
VI. COMPONENTS
14MY 4Runner
Replacement Items in red
No. Contents of Part Kit’s Quantity Tape Color Remarks
1
FUEL PUMP
1
2
FUEL SUCTION TUBE SET GASKET
1
3
O-RING
1
Yellow
15.2mm
4
FUEL PUMP GAUGE RETAINER
1
DO NOT order the individual parts listed here. It is provided as a reference to assist in the correct installation. Order the parts kit’s specific to each VIN, as detailed in the parts lookup website (p. 4).
Warranty will only reimburse dealers for the part numbers listed on the website. Any other part numbers will not be accepted on the campaign claim.
8
AVALON 2019
Replacement items in red
No. Contents of Part Kit’s Quantity Tape Color Remarks
1
FUEL PUMP
1
2
FUEL SUCTION TUBE SET GASKET
1
3
O-RING
2*
Gold
15.2mm
4
REAR SEAT CUSHION LOCK HOOK
2
Not used
5
O-RING
1
Red
Not used
6
O-RING
1
Green
Not used
7
FUEL TANK PIPE SETTING HOLDER
1
White
Not used
8
REAR SEAT CUSHION LOCK HOOK
2
*only 1 O-Ring will be used. Discard the 2nd O-Ring.
DO NOT order the individual parts listed here. It is provided as a reference to assist in the correct installation. Order the parts kit’s specific to each VIN, as detailed in the parts lookup website (p. 4).
Warranty will only reimburse dealers for the part numbers listed on the website. Any other part numbers will not be accepted on the campaign claim.
Note: Some items in the Fuel Pump Replacement Kit will not be used.
9
CAMRY
Replacement items in red
No. Contents of Part Kit’s Quantity Tape Color Remarks
1
FUEL PUMP
1
2
FUEL SUCTION TUBE SET GASKET
1
3
O-RING
2*
Gold
15.2mm
4
REAR SEAT CUSHION LOCK HOOK
2
Not used
5
O-RING
1
Red
Not used
6
O-RING
1
Green
Not used
7
FUEL TANK PIPE SETTING HOLDER
1
White
Not used
8
REAR SEAT CUSHION LOCK HOOK
2
*only 1 O-Ring will be used. Discard the 2nd O-Ring.
DO NOT order the individual parts listed here. It is provided as a reference to assist in the correct installation. Order the parts kit’s specific to each VIN, as detailed in the parts lookup website (p. 4).
Warranty will only reimburse dealers for the part numbers listed on the website. Any other part numbers will not be accepted on the campaign claim.
Note: Some items in the Fuel Pump Replacement Kit will not be used.
10
COROLLA
Replacement items in red
No. Contents of Part Kit’s Quantity Tape Color Remarks
1
FUEL PUMP
1
2
O-RING
1
(not labeled)
13.2mm
3
FUEL SUCTION TUBE SET GASKET
1
4
FUEL PUMP GAUGE RETAINER
1
5
REAR SEAT CUSHION LOCK HOOK
2
6
FUEL PIPE SETTING HOLDER
1
DO NOT order the individual parts listed here. It is provided as a reference to assist in the correct installation. Order the parts kit’s specific to each VIN, as detailed in the parts lookup website (p. 4).
Warranty will only reimburse dealers for the part numbers listed on the website. Any other part numbers will not be accepted on the campaign claim.
11
FJ CRUISER
Replacement items in red
No. Contents of Part Kit’s Quantity Tape Color Remarks
1
FUEL PUMP
1
2
FUEL SUCTION TUBE SET GASKET
1
3
O-RING
1
Yellow
15.2mm
4
FUEL PUMP GAUGE RETAINER
1
DO NOT order the individual parts listed here. It is provided as a reference to assist in the correct installation. Order the parts kit’s specific to each VIN, as detailed in the parts lookup website (p. 4).
Warranty will only reimburse dealers for the part numbers listed on the website. Any other part numbers will not be accepted on the campaign claim.
12
HIGHLANDER
Replacement items in red
No. Contents of Part Kit’s Quantity Tape Color Remarks
1
FUEL PUMP
1
2
FUEL SUCTION TUBE SET GASKET
1
3
FUEL PUMP GAUGE RETAINER
1
4
FUEL TANK PIPE SETTING HOLDER
1
5
O RING
1
(not labeled)
DO NOT order the individual parts listed here. It is provided as a reference to assist in the correct installation. Order the parts kit’s specific to each VIN, as detailed in the parts lookup website (p. 4).
Warranty will only reimburse dealers for the part numbers listed on the website. Any other part numbers will not be accepted on the campaign claim.
13
SEQUOIA
TUNDRA
Replacement items in red
No. Contents of Part Kit’s Quantity Tape Color Remarks
1
FUEL PUMP
1
2
FUEL SUCTION TUBE SET GASKET
1
3
FUEL PUMP GAUGE RETAINER
1
4
O-RING
1
(not labeled)
DO NOT order the individual parts listed here. It is provided as a reference to assist in the correct installation. Order the parts kit’s specific to each VIN, as detailed in the parts lookup website (p. 4).
Warranty will only reimburse dealers for the part numbers listed on the website. Any other part numbers will not be accepted on the campaign claim.
14
VII. REMOVE FUEL TUBE ASSEMBLY
Use TIS to confirm that this vehicle is eligible for the campaign before proceeding (p. 3). Warranty will not pay claims on ineligible vehicles.
1. CHECK FOR DTC’S
a. Using a Techstream, perform a Health Check to check for Diagnostic Trouble Codes.
Note: This Safety Recall covers only the replacement of the fuel pump and associated parts. It does not cover the diagnosis or replacement of any other parts on the vehicle.
REMOVAL TIP: FUEL LEVEL
If the fuel level inside the fuel tank is above the specified level, fuel may overflow from the fuel tank during the removal of the fuel suction tube assembly. Confirm the fuel level in the vehicle is below the specified level before proceeding. If necessary, drain fuel from the tank.
FUEL LEVEL RECOMMENDATIONS
Model
Less than full
3/4 or less
4Runner
Avalon
Camry
Corolla
FJ Cruiser
Highlander
Sequoia
Tundra
Note: If fuel needs to be removed from the tank, be sure to recover it into an approved fuel recovery system. Suitable systems are available from the Toyota Approved Dealer Equipment website.
15
REMOVAL TIP: PLASTIC RING RETAINERS
If removing the Plastic Ring type retainers, cut the 4 internal claws to prevent the Fuel Tube assembly from rotating during removal. This could cause damage to the fuel level sender, fuel tank, or fuel tube assembly.
REMOVAL TIP: TUBE ASSY ALIGNMENT
For vehicles with the plastic retainer rings, place matchmarks on both the Fuel Tube Assembly and the fuel tank. During disassembly, confirm that the Fuel Tube Assembly does not rotate. During reassembly, this will aid in aligning the locating tabs for proper installation.
16
REMOVAL TIP: CAM LOCK RETAINER TOOL
An updated set of Cam Lock Claws and Support Columns are being supplied to each dealership for this campaign. The configuration of the retainer engagement sections of the claws have been modified from the SST that is referenced in the repair manual. The NEW claws have an improved design that enables a firm attachment to the retainer. In addition, 2 support columns are provided which will support the retainer more securely during installation and removal. Be sure to assemble and use the tools using the following procedures:
Campaign Tool Cam Lock Set:
17
REMOVAL TIP: CAM LOCK RETAINER TOOL (cont.)
Lightly tighten the adjuster
Fully tighten the 4 bolts
2. REMOVE FUEL TUBE ASSEMBLY FROM VEHICLE
a. Follow the Repair Manual instructions to remove the Fuel Tube Assembly from the vehicle.
REMOVE FUEL TUBE ASSY.
Tundra
1UR-FE 4.6
2018
2019
Highlander
2018 2019
Tundra
3UR-FE 5.7
2018
2019
FJ Cruiser
2014
Sequoia
2018
2019
Avalon
2019
Camry
2018
2019
4Runner
2014
Corolla
2018
2019
18
VIII. DISASSEMBLY OF FUEL TUBE
DISASSEMBLY TIP: FOLLOW THE REPAIR MANUAL
The Part’s Kit contains the necessary O-Rings for reassembly, if the Repair Manual procedure is followed. If the pump components are disassembled in a manor other than as detailed in the Repair Manual, the Parts Kit may not contain the necessary O-Rings for proper reassembly. Please follow the procedures in the Repair Manual to ensure the correct O-Rings are available.
Example of Proper Disassembly:
Repair Manual: Using a screwdriver (*a) with its tip wrapped in protective tape, remove the jet pump from the No. 1 fuel sub-tank.
Tube still attached
Jet pump properly removed from
the No.1 fuel sub-tank.
Replacement O-Ring will be
installed in this location
Example of Incorrect Disassembly:
Tube incorrectly removed from jet pump
Replacement O-ring is the incorrect size
DO NOT disconnect the tube from the jet pump
Replacement O-Ring is NOT provided for this location
19
DISASSEMBLY TIP: MAIN VALVE AND REGULATOR
When replacing the fuel pump, it is not necessary to remove the Fuel Main Valve or Fuel Pressure Regulator. These O-Rings are NOT included in the parts kit.
DISASSEMBLY TIPS: FUEL FILTER
Many of the models will require the fuel filter to be reused. Be careful with the tabs when removing the filter from the original fuel pump as to not overextend them. When installing the filter on the NEW Fuel Pump, be sure that the clips have engaged properly.
1. DISASSEMBLE FUEL SUCTION TUBE ASSEMBLY
a. Follow the Repair Manual instructions to disassemble the Fuel Suction Tube Assembly.
DISASSEMBLE
Tundra
1UR-FE 4.6
2018
2019
Highlander
2018 2019
Tundra
3UR-FE 5.7
2018
2019
FJ Cruiser
2014
Sequoia
2018
2019
Avalon
2019
Camry
2018
2019
4Runner
2014
Corolla
2018
2019
20
2. CLEAN SUB TANK ASSEMBLY
a. Using brake cleaner, clean the sub-tank assembly.
IX. REASSEMBLE FUEL TUBE ASSEMBLY
REASSEMBLY TIPS: O-RINGS
The part kits may come with O-Rings of different sizes. They are very difficult to tell apart visually. To identify the different size O-Rings, they will be wrapped in individual plastic bags with a piece of COLORED TAPE sealing it. The COLOR OF THE TAPE will identify the O-Ring size. REFER TO THE COMPONENT DIAGRAMS TO DETERMINE TO CORRECT O-RING, as identified by the tape color.
1. CONFIRM PARTS
a. Using the part lookup website, input the VIN number to confirm that you have the proper parts for this vehicle:
https://20ta02.imagespm.info
To log into the website:
a. Enter your dealer code in the Dealer Code field.
b. Enter XXXXX (5 Capital X’s) for the Password.
21
2. REASSEMBLE FUEL SUCTION TUBE ASSEMBLY WITH NEW FUEL PUMP
a. Follow the Repair Manual instructions to reassemble the Fuel Suction Tube Assembly with a NEW Fuel Pump.
Refer to the Component diagrams at the beginning of these Technical Instructions to confirm the location of each replacement part.
Example Procedure:
HINT:
The reused filter may be discolored.
• Remove the original O-Ring, Spacer and Fuel Filter from the original Fuel Pump.
• Discard the original O-Ring and Fuel Pump, saving the Spacer and Fuel Filter.
• Install the original Spacer onto the NEW Fuel Pump.
• Install the NEW O-Ring onto the NEW Fuel Pump. Refer to the Component Diagram to determine to proper O-Ring, as identified by the colored tape on the bag.
• Apply a small amount of engine oil to the NEW O-Ring to assure correct installation into the Tube Assembly.
• Install the original Fuel Filter onto the NEW Fuel Pump.
• Refer to the Components diagrams to review the other NEW parts to install.
• Apply engine oil to the NEW O-ring before assembly to assure correct installation into the Fuel Suction Tube.
3. REASSEMBLE FUEL SUCTION TUBE ASSEMBLY
b. Follow the Repair Manual instructions to reassemble the Fuel Suction Tube Assembly.
REASSEMBLE
Tundra
1UR-FE 4.6
2018
2019
Highlander
2018 2019
Tundra
3UR-FE 5.7
2018
2019
FJ Cruiser
2014
Sequoia
2018
2019
Avalon
2019
Camry
2018
2019
4Runner
2014
Corolla
2018
2019
22
X. INSTALL FUEL TUBE ASSEMBLY
INSTALLATION TIP: PLASTIC RETAINER
23
1. INSTALL THE FUEL SUCTION TUBE ASSEMBLY INTO VEHICLE
a. Follow the Repair Manual instructions to reinstall the Fuel Suction Tube into the vehicle.
Refer to the Component diagrams at the beginning of these Technical Instructions to confirm the location of each replacement part.
INSTALLATION
Tundra
1UR-FE 4.6
2018
2019
Highlander
2018 2019
Tundra
3UR-FE 5.7
2018
2019
FJ Cruiser
2014
Sequoia
2018
2019
Avalon
2019
Camry
2018
2019
4Runner
2014
Corolla
2018
2019
2. INSTALL REMOVED FUEL
a. If fuel was removed from the tank prior to disassembly, reinstall the originally recovered fuel into the tank.
3. CHECK FOR DTC’S
a. Using a Techstream, perform a Health Check to check for Diagnostic Trouble Codes.
Note: This Safety Recall covers only the replacement of the fuel pump and associated parts. It does not cover the diagnosis or replacement of any other parts on the vehicle.
◄ VERIFY REPAIR QUALITY ►
• Confirm no fuel leaks from vehicle
• Confirm any fuel drained from the vehicle has been reinstalled
• Test drive to confirm normal operation while under load
• Confirm no DTC’s are present
• Confirm that all parts listed in the Components Diagrams have been properly installed on the vehicle.
24
19
19 = 2019
20 = 2020
21 = 2021
22 = 2022
23 = 2023
Etc…
Year Campaign
is Launched
19TA01
T
T = Toyota
L = Lexus
Vehicle Make
A
A = Safety Recall Remedy
B = Safety Recall Interim
C = Special Service Campaign
D = Limited Service Campaign
E = Customer Support Program
F = Emissions Recall
(May use other characters in unique
cases)
Field Action Category and Phase
01
01 = 1st Field Action of the year
02 = 2nd Field Action of the year
03 = 3rd Field Action of the year
(The sequence is unique for each
Field Action category)
(May use other characters in
unique cases)
Field Action Sequence
Examples:
19TA01 = Launched in 2019, Toyota, Safety Recall Remedy Phase, 1st Safety Recall Launched in 2019
20TC02 = Launched in 2020, Special Service Campaign, 2nd Special Service Campaign Launched in
2020
21TE05 = Launched in 2021, Customer Support Program, 5th Customer Support Program Launched
in 2021
XI. APPENDIX
A. PARTS DISPOSAL
In accordance with Federal law, please make sure all recalled parts (original parts)
removed from the vehicle are disposed of in a manner in which they will not be reused,
unless requested for parts recovery return.
B. CAMPAIGN DESIGNATION DECORDER
SEOCONTENT-END
Remedy Instructions and TSB
RCRIT-20V012-6173.pdf 2253.879KB
Remedy Instructions and TSB
RCRIT-20V012-5730.pdf 2298.048KB
Remedy Instructions and TSB
RCRIT-20V012-1152.pdf 2292.389KB
- ✅ Effortless Cleaning | Simply rinse off any residue for a quick clean-up. FCC approved for your safety.
- ✅ Odorless Operation | Our decarboxylator, made from food-grade materials, ensures perfect odor control during decarboxylation.
- ✅ Ample Capacity | The aluminum canister of this infuser activates up to 2 ounces of herb and products.
- ✅ Smart and Simple | Straightforward 2 preset modes for infusion and decarboxylation, maximizing the results effortlessly.
- ✅ Accurate Heating | The canister's wall and bottom heating ensure precise temperatures for optimal decarb.
- This item is not for sale in Catalina Island
- Make Delicious Edibles at Home: With the push of a button! Create perfectly infused butters, oils and tinctures for use with all your favorite recipes. Use the clear lid to watch your infusions in action (also great as a tincture machine).
- Decarb, Infuse & Mix: Easily decarb and infuse your herbs in 1 device! The herbal infuser machine can decarb up to 1.5 oz of flower and infuse up to 2 cups of butter, oil or tincture! No more decarb boxes or ovens. Now with a new Gummy Mixer Mode, to make gummies even easier. This device does it all.
- Includes Everything You Need: Infusion Buds 3-IN-1 extractor machine for decarbing, infusing, and mixing gelatin, 3 gummy molds, a butter mold with lid, Infuser & Gummy Mixer attachment, custom strainer & press, and Physical Recipe Book.
- Endless Recipes & Free Cookbook: Use your butter with any of your favorite recipes: brownies, cookies, smoothies, sauces, candies, beverages and much more. Dozens of recipes and tips included in your recipe book.
- 1 Year warranty: As an American owned brand, we stand behind our products. We offer freindly support and include a warranty card with every purchase. Our friendly, customer service team is her to help you every step of the way.
- Ultimate Machine and Accessories Set: Get everything you need for perfect homemade edibles with our all-inclusive bundle. It includes the Decarb9 thermometer machine, airtight food grade silicone decarb box. Measuring 7.75”x5.25”x2.25”
- Infuse with Precision: Achieve optimal potency and flavor with the high-precision electric thermometer and timer alarm. This ensures maximum activation efficiency and consistent results every time, making it a must-have for any serious edible maker.
- Odorless and Hassle-Free: The Decarb9's sealed lid and full enclosure design eliminate odors and provide a smell-proof decarb experience. Plus, the non-stick silicone construction makes cleaning a breeze, and it's both dishwasher and microwave safe.
- Effortless and Efficient: With the dual-prob angel design, our Decarb9 fits perfectly in personal ovens, allowing you to decarboxylate up to 2 ounces of material with ease. Say goodbye to guesswork and over decarboxylation.
- Elevate Your Edibles: Take your homemade edibles to the next level with our premium set. Enhance your creativity with gummy molds, candy, infuse oil. Give the perfect gifts for aspiring edible enthusiasts and a great addition to any infuser's kitchen arsenal.
- Make Delicious Edibles at Home: With the push of a button! Create perfectly infused butters, oils and tinctures for use with all your favorite recipes.
- Decarb & Infuse: Easily decarb and infuse your herbs in 1 device. The device can decarb up to 1.5 oz of flower and infuse up to 2 cups of butter, oil or tincture! No more decarb boxes or ovens.
- Includes everything you need: Infusion Buds extractor machine for decarbing and infusing, 3 gummy molds, butter mold with lid, custom strainer & press, and an easy clean Infusion Insert.
- Endless recipes & cookbook: Use your butter with any of your favorite recipes: brownies, cookies, smoothies, sauces, candies, beverages and much more. Dozens of recipes and tips included in your book.
- As an American owned and opperated business, we stand behind our products. We offer freindly support and include a warranty card with every purchase. Our friendly, customer service team is her to help you every step of the way.
- EFFORTLESS INFUSION: The Ardent Mini simplifies creating edibles and infusions with one compact device. With just a push of a button, you can infuse oils, butters, and more. It accommodates up to 1 ounce of herbs and infuses up to 6 ounces of oil, ensuring consistent, flavorful results every time.
- VERSATILE FUNCTIONALITY: Ardent Mini offers customizable modes to decarboxylate and infuse herbs into oils, butters, MCT oil, chocolate, honey, and more, with precision. Switch between A1 and A2 modes to tailor the process for different applications, ensuring effective and potent results. You can even bake a small treat directly inside the unit using the activated material or infusion on the A2 setting.
- PRECISION, WITHOUT THE SMELL: Thanks to its odorless technology, the Ardent FX keeps your kitchen free of unwanted smells while maintaining precise control over your infusions and decarboxylation, ensuring potent results every time.
- PREMIUM MATERIALS: The Ardent FX mini uses non-toxic, food-grade silicone ensuring that your infusions are safe and high quality. Its removable parts are easy to clean and dishwasher safe, making cleanup quick and convenient.
- SET IT, FORGET IT, ENJOY IT: With two temperature settings, the Ardent FX mini makes it easy to create consistent, potent infusions. Its automatic cycles make the process worry-free, so you can focus on enjoying your creations.
- VERSATILE MACHINE: A 3-in-1 decarboxylator, herb infuser, and gummy maker with a mixing function for seamless herbal extraction and infusion.
- PRECISE CONTROLS: Digital control panel allows you to set precise time and temperature for optimal extraction.
- EFFICIENT EXTRACTION: The silicone stirring tool will help evenly heat herbs during the decarboxylation and infusion processes,efficiently decarbing and extract active compounds from herbs into oils, butters, or alcohol-based tinctures. The metal stirring tool will help the oil infuse evenly in the gummy mixture.
- COMPREHENSIVE KIT: Comes with a stainless steel strainer, oil & tincture press, silicone gummy molds, and a recipe book for creative herbal recipes
- COMPACT SIZE: Sleek design, making it a stylish and space-saving addition to any kitchen. Tips: The device needs to be turn on/ off by long pressing the On/Off button for 1.5 seconds
- Restores mobility of stuck piston rings
- Reduces oil consumption
- Cleans cylinders and pistons, combustion chambers and valves from any kind of deposits (sludge, carbon, etc)
- Equalizers compression in cylinders
- Decreases noise while engine operating
Last update on 2025-03-18 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.